Line 1: |
Line 1: |
| [[Category:How to]] | | [[Category:How to]] |
| '''This section contains the suggested prefix digits, mandatory command codes, and suggested command codes for Allstar Link.''' | | '''This section contains the suggested prefix digits, mandatory command codes, and suggested command codes for Allstar Link.''' |
| + | |
| + | == Prefix Digit Suggestions == |
| + | PrefixFunctions |
| + | |
| + | <nowiki>*</nowiki>1Disconnect Link |
| + | |
| + | <nowiki>*</nowiki>2Monitor Link |
| + | |
| + | <nowiki>*</nowiki>3Connect Link |
| + | |
| + | <nowiki>*</nowiki>4Command Mode |
| + | |
| + | <nowiki>*</nowiki>5Macros |
| + | |
| + | <nowiki>*</nowiki>6User Functions |
| + | |
| + | <nowiki>*</nowiki>7Connection Status/Functions |
| + | |
| + | <nowiki>*</nowiki>8User Functions |
| + | |
| + | <nowiki>*</nowiki>9User Functions |
| + | |
| + | <nowiki>*</nowiki>0User Functions |
| + | |
| + | <nowiki>*</nowiki>AUser Functions |
| + | |
| + | <nowiki>*</nowiki>BUser Functions |
| + | |
| + | <nowiki>*</nowiki>CUser Functions |
| + | |
| + | <nowiki>*</nowiki>DUser Functions |
| + | |
| + | == Mandatory Command Codes == |
| + | These are the mandatory command codes which all Allstar Link nodes must support to provide command code consistency to the users. |
| + | Command CodeDescription |
| + | |
| + | <nowiki>*</nowiki>1<code>node</code>Disconnect Link |
| + | |
| + | <nowiki>*</nowiki>2<code>node</code>Connect link in monitor mode |
| + | |
| + | <nowiki>*</nowiki>3<code>node</code>Connect link in transcieve mode |
| + | |
| + | <nowiki>*</nowiki>4<code>node</code>Enter command mode on a remote node |
| + | |
| + | <nowiki>*</nowiki>70Local connection status |
| + | |
| + | <nowiki>*</nowiki>99DTMF Phone Key (Assert PTT from Phone Portal) |
| + | |
| + | Notes |
| + | # <code>node</code> is an Allstar Link node number |
| + | # Node number zero (0) is shorthand for the last node operated on by a previous command |
| + | # Monitor mode means listen to a node, but do not send any audio to it |
| + | # Command mode means send all received DTMF digits to the node number specified (bypassing the local command decoder). Send # to exit command mode, and restore local command decoding. |
| + | |
| + | == Optional Command Codes == |
| + | Command CodeDescription |
| + | <nowiki>*</nowiki>80Force System ID |
| + | |
| + | <nowiki>*</nowiki>81Say System Time |
| + | |
| + | <nowiki>*</nowiki>980Say app_rpt software version |
| + | |
| + | <nowiki>*</nowiki>75Link Connect (Local Monitor Only) |
| + | |
| + | <nowiki>*</nowiki>72Last active node (system-wide) |
| + | |
| + | <nowiki>*</nowiki>73System-wide connection status |
| + | |
| + | <nowiki>*</nowiki>71Disconnect all links (macro) |
| + | |
| + | <nowiki>*</nowiki>74Reconnect all links (macro) |