Line 1: |
Line 1: |
| [[Category:How to]] | | [[Category:How to]] |
− | '''This section contains the suggested prefix digits, mandatory command codes, and suggested command codes for Allstar Link.''' | + | '''This section contains the suggested prefix digits, mandatory command codes, and suggested command codes for PTTLink.''' |
| + | |
| + | == Prefix Digit Suggestions == |
| + | PrefixFunctions |
| + | |
| + | <nowiki>*</nowiki>1 Disconnect Link |
| + | |
| + | <nowiki>*</nowiki>2 Monitor Link |
| + | |
| + | <nowiki>*</nowiki>3 Connect Link |
| + | |
| + | <nowiki>*</nowiki>4 Command Mode |
| + | |
| + | <nowiki>*</nowiki>5 Macros |
| + | |
| + | <nowiki>*</nowiki>6 User Functions |
| + | |
| + | <nowiki>*</nowiki>7 Connection Status/Functions |
| + | |
| + | <nowiki>*</nowiki>8 User Functions |
| + | |
| + | <nowiki>*</nowiki>9 User Functions |
| + | |
| + | <nowiki>*</nowiki>0 User Functions |
| + | |
| + | <nowiki>*</nowiki>A User Functions |
| + | |
| + | <nowiki>*</nowiki>B User Functions |
| + | |
| + | <nowiki>*</nowiki>C User Functions |
| + | |
| + | <nowiki>*</nowiki>D User Functions |
| + | |
| + | == Mandatory Command Codes == |
| + | These are the mandatory command codes which all PTTLink nodes must support to provide command code consistency to the users. |
| + | |
| + | Command CodeDescription |
| + | |
| + | <nowiki>*</nowiki>1<code>node</code>Disconnect Link |
| + | |
| + | <nowiki>*</nowiki>2<code>node</code>Connect link in monitor mode |
| + | |
| + | <nowiki>*</nowiki>3<code>node</code>Connect link in transcieve mode |
| + | |
| + | <nowiki>*</nowiki>4<code>node</code>Enter command mode on a remote node |
| + | |
| + | <nowiki>*</nowiki>70 Local connection status |
| + | |
| + | <nowiki>*</nowiki>99 DTMF Phone Key (Assert PTT from Phone Portal) |
| + | |
| + | Notes |
| + | # <code>node</code> is an PTTLink node number |
| + | # Node number zero (0) is shorthand for the last node operated on by a previous command |
| + | # Monitor mode means listen to a node, but do not send any audio to it |
| + | # Command mode means send all received DTMF digits to the node number specified (bypassing the local command decoder). Send # to exit command mode, and restore local command decoding. |
| + | |
| + | == Optional Command Codes == |
| + | Command CodeDescription |
| + | |
| + | <nowiki>*</nowiki>80 Force System ID |
| + | |
| + | <nowiki>*</nowiki>81 Say System Time |
| + | |
| + | <nowiki>*</nowiki>980 Say app_rpt software version |
| + | |
| + | <nowiki>*</nowiki>75 Link Connect (Local Monitor Only) |
| + | |
| + | <nowiki>*</nowiki>72 Last active node (system-wide) |
| + | |
| + | <nowiki>*</nowiki>73 System-wide connection status |
| + | |
| + | <nowiki>*</nowiki>71 Disconnect all links (macro) |
| + | |
| + | <nowiki>*</nowiki>74 Reconnect all links (macro) |