Line 275: |
Line 275: |
| Enter Selection (1-9,99,c,x,q,r) : | | Enter Selection (1-9,99,c,x,q,r) : |
| </pre> | | </pre> |
| + | |
| + | =Configuration Options= |
| + | ==Main Menu Options== |
| + | ===Serial #=== |
| + | Sets the serial number for the RTCM/VOTER. |
| + | *This sets the MAC address of the unit |
| + | *Each unit must have a unique serial number on your network segment |
| + | |
| + | ===VOTER Server Address (FQDN)=== |
| + | This is the DNS name or IP address of the Asterisk server you are connecting to. |
| + | |
| + | ===VOTER Server Port=== |
| + | This is the UDP port that the Asterisk server is listening on for clients. |
| + | *Typically it is left at the default of port 667 |
| + | *'''MUST''' match the ''port'' directive in ''voter.conf'' |
| + | |
| + | ===Local Port (Override)=== |
| + | Sets the local unit UDP port to be something different. |
| + | *This is typically not used and left at default (0) |
| + | |
| + | ===Client Password=== |
| + | This is the '''unique''' password for this unit. |
| + | *Every unit '''must''' have a '''unique''' password |
| + | *'''MUST''' match the password on the client configuration line in ''voter.conf'' |
| + | |
| + | ===Host Password=== |
| + | This is the password of the Asterisk server. |
| + | *Configured with the ''password'' directive in ''voter.conf'' |
| + | |
| + | |
| + | ===Tx Buffer Length=== |
| + | This is the size of the TX buffer from the RTCM/VOTER to the Asterisk server. |
| + | *Tuned parameter, set via the tuning instructions based on network configuration |
| + | |
| + | ===GPS Data Protocol (0=NMEA, 1=TSIP)=== |
| + | Type of GPS connected. |
| + | *NMEA for all non-Trimble GPS units |
| + | *TSIP to use with Trimble GPS that use Trimble Serial Interface Protocol (TSIP) |
| + | |
| + | ===GPS Serial Polarity (0=Non-Inverted, 1=Inverted)=== |
| + | GPS dependent setting. |
| + | *Depends on if you are sending TTL or RS-232 data, adjust as needed. |
| + | |
| + | ===GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE)=== |
| + | GPS dependent setting. |
| + | *Depends on if you are sending TTL or RS-232 data for the PPS signal, adjust as needed. |
| + | *If not using GPS or configuring as a mixed client, set to 2 (None). |
| + | |
| + | ===GPS Baud Rate=== |
| + | Communication speed for the GPS, default is 9600. |
| + | |
| + | ===External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted)=== |
| + | If you are using the CTCSS input from an external CTCSS decoder, adjust this for your logic polarity, or set to 0 (ignore) if not used. |
| + | |
| + | |
| + | ===COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver)=== |
| + | Typically, this is left at Normal. |
| + | *Set to 1 (Ignore COR), if you are using the External CTCSS input. |
| + | |
| + | ===Debug Level=== |
| + | Set the Debug Level, if needed, based on the [[#Debug Options | Debug Options]] below |
| + | |
| + | ===Alt. VOTER Server Address (FQDN)=== |
| + | If you are using redundant Asterisk servers, set the IP/DNS address of the redundant server here. |
| + | |
| + | ===Alt. VOTER Server Port (Override)=== |
| + | If the redundant Asterisk server UDP port is not 667, set it here. |
| + | |
| + | ===DSP/BEW Mode=== |
| + | If the firmware supports DSP/BEW Mode, set this to 1 to enable it, if desired. |
| + | *DSP/BEW firmware versions use extra firmware space and will make the diagnostic menu unavailable. |
| + | |
| + | |
| + | ==="Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs)=== |
| + | If you are using Duplex Mode 3, set the hang time here to enable the option. Most users leave this disabled. |
| + | |
| + | ===Simulcast Launch Delay=== |
| + | If you are using Simulcast, set your launch delay here. |
| + | |
| + | ===RX Level=== |
| + | This opens the RX Level tuning screen to adjust the receive audio level from the repeater. |
| + | |
| + | ===Status=== |
| + | This opens the status menu, showing some of the current operating parameters. |
| + | |
| + | ===Save Values to EEPROM=== |
| + | Save all the options to non-volatile EEPROM. |
| + | *Make sure to save after you make any changes. |
| + | |
| + | ===IP Parameters menu=== |
| + | Open the IP Parameters Menu. |
| + | |
| + | ===Offline Mode Parameters menu=== |
| + | Open the Offline Mode Parameters Menu. |
| + | |
| + | ===Disconnect Remote Console Session=== |
| + | If you are connected via Telnet, this will exit your session. |
| + | |
| + | ===Reboot System=== |
| + | Reboot the VOTER/RTCM. |
| + | *This should be done after making configuration changes. |
| + | *Some setting changes require a reboot to become effective. |
| + | |
| + | ===Diagnostics=== |
| + | Open the Diagnostics Menu. |
| + | *Diagnostics are unavailable if you are using DSP/BEW firmware. |
| | | |
| | | |