Search results

This page discusses interfacing the Motorola Quantar to the RTCM/VOTER interface, for use with AllStar. This page should get you up and running with how

Astro-TAC/RTCM Interface Cable Interfacing to a Quantar with P25Link and P25NX - Bryan Fields W9CR has page on interfacing the Qunatar using simple USB into PTTLink

Interfacing the GM300

commercially available hardware for interfacing radios to an PTTLink computer. The Micro-Node RTCM and VOTER interfaces are typically used with PTTLink in

meant to be used in conjunction with linktolink, inxlat, and outxlat when interfacing a radio port to a multiport analog repeater controller on an RF-linked

Chan_usbradio is a feature rich DSP radio interface. It requires more CPU than chan_simpleusb and therefor chan_simpleusb may be a better choice on smaller

addtap.bat netsh interface ipv4 show interfaces (Note disconnected interface. May be called Ethernet 2) netsh interface set interface name = "Ethernet

This file sets up the app_rpt interface to an RTCM. The RTCM may be used in any of 3 modes; non-voting client mode, voting mode or voting and simulcast

use /etc/network/interfaces, and add DNS and the firewall to it and search in the allstarlink.org domain # The primary network interface auto eth0 iface

you wish to support. For USB interfaces, more processor horsepower is necessary. If you are going to use a USB interface, then the CPU speed should ne

needed for the interface. If the compiled in IP is matched, it will return a dump of the database. jsondata.cgi - not needed for the interface, used for returning

The chan_voter channel driver is the interface between Asterisk and the RTCM/VOTER radio/repeater hardware interface. It allows receiver voting, simulcast

default | cut -d' ' -f 3` && \ echo "/ip address add address=$ADDRESS interface=[/interface ethernet find where name=ether1] /ip route add gateway=$GATEWAY "

a Virtual Machine in a data center. Multiple repeaters (nodes) may be interfaced at one site while only running one instance of Asterisk/app_rpt on one

confuse the USB channel driver and require that usbradio.conf have all the interfaces removed or commented out and added back in one at a time. The use of USB

instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces. rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed

bryan@StPeteRpt:~ $ sudo dahdi_test [sudo] password for bryan: Opened pseudo dahdi interface, measuring accuracy... 99.614% 99.594% 99.608% 99.608% 98.476% 99.638%

users not familiar with linux and PttLink, at the Linux CLI (command line interface) Type sudo asl-menu as the example below shows. repeater@repeater:~$ sudo

Raid 50 config. It's primary IP is 44.98.254.129/27 which is a logical interface "44net" on the 44net bridge. enp3s0f0 is 208.38.136.11 and is physically

AT93C46E-PU (Digikey Part Number AT93C46E-PU-ND) or equiv. to the URI via the interface connector, thereby allowing the USBRadio channel driver's working parameters

An assigned dedicated node number (e.g. pttlink.org) A radio interface A radio interface cable A supported radio A new or existing PC host computer Remote

EEProm to save parameters, please see https://wiki.allstarlink.org/wiki/Interface_EPROM_to_URI Motorola Desktrac Repeater - Flat audio Tie Desktrac 20 and

side (the "A" side) is an interface between the DMK URI and the Kenwood TMG-707A. The other side (the "B" side) is an interface between the 4 port PCI CARD

This section is circa 2005, and is out of date. It is possible to interface an app_rpt installation with TheLinkBox Program (by Skip, WB6YMH), using the

This how-to describes how to properly set audio levels with a URI interfaced to a radio when using chan_usbradio. Required Equipment Communications service

access to the machine being calibrated. Tweaking tools if your radio or interface board have physical adjustment pots, or the appropriate service software

optionally support the Quad Port pciradio interface card. This card is basically a 4 port simple usb interface, but designed to slot in a PCI bus. Intel

as IAX, or Echolink and the common interface used inside of Asterisk. Think of channel drivers as protocol interfaces. The channel drivers most frequently

features, new source code is posted to SVN (and available from the viewvc interface) from time to time. New installs do not get the latest updates as what

LPT3 respectively. If you might imagine you may use a Doug Hall RBI-1 interface, then begin populating Parallel Port pins starting after pp3 (pin5) as

FM radio. The following settings can be optionally used in a USB radio interface context in "/etc/asterisk/usbradio.conf". If these keyword and value pairs

users not familiar with linux and PTTLink, at the Linux CLI (command line interface) Type sudo ptt-menu as the example below shows. sudo ptt-menu This will

flashing once the system is completely booted. Now, the radio should be interfaced and the audio levels adjusted using the USB FOB setup procedures located here

used to view the current status of PTTLink systems via the provided web interface. For all other systems not explicitly listed here: No data may be scraped

is for those users who have a compatible motherboard, and a URI radio interface. Using Limey Linux with the Quad Radio PCI card is feasible, but is beyond

que no están familiarizados con Linux, PTTLink y Linux CLI (command line interface), pueden seguir paso a paso el procedimiento: Escribe sudo ptt-menu como

que no están familiarizados con Linux, PTTLink y Linux CLI (command line interface), pueden seguir paso a paso el procedimiento: Escribe sudo asl-menu como

functionality, providing an Asterisk channel which app_rpt may open as a radio interface (like a usbradio or pseudo channel in a non-voting AllstarLink system)