Cable Adapter Card for TMG-707A - Revision history

N8THN: Added links to PDF's

2019-01-28T04:17:24Z

Added links to PDF's

N8THN: disabled text wrap around images

2019-01-28T03:45:20Z

disabled text wrap around images

N8THN: added images

2019-01-28T03:43:33Z

added images

N8THN: created page

2019-01-28T03:28:12Z

created page

New page

[[Category:URI]]
Cable Adapter Card for TMG-707A

@@ Line 42: / Line 42: @@
 The Bill of Materials for the whole card (including DIGIKEY part
-numbers may be accessed here.
+numbers may be accessed [https://wiki.allstarlink.org/w/images/2/20/9088_Updated_BOM.pdf here].
 Note: This Bill of Materials is for the BOTH halves of the board.
@@ Line 50: / Line 50: @@
 the half you dont want.
-And for those who are interested here is the schematic.
+And for those who are interested here is the [https://wiki.allstarlink.org/w/images/3/31/9088_schematic.pdf schematic].

@@ Line 7: / Line 7: @@
 Hi-res Photo:
-[[File:9088A.jpg|left|thumb]]
+[[File:9088A.jpg|thumb|none]]
+.
@@ Line 21: / Line 21: @@
 Here is an example of a fully-constructed "A" side:
-[[File:9088-A.jpg|left|thumb|9088-A Interface board]]
+[[File:9088-A.jpg|thumb|9088-A Interface board|none]]
+.
@@ Line 29: / Line 29: @@
 Here is an example of a fully-constructed "B" side:
-[[File:9088-B.jpg|left|thumb]]
+[[File:9088-B.jpg|thumb|none]]
+.

← Older revision		Revision as of 03:43, 28 January 2019
Line 1:		Line 1:
	[[Category:URI]]		[[Category:URI]]
−	~~Cable Adapter Card~~ for TMG-707A	+	This card (bare-board) is available from Marshall Oldham [[Mailto:ke6pcv@cal-net.org\|ke6pcv@cal-net.org]]
		+
		+	for $20.00 USD. It uses all standard thru-hole parts that takes very
		+
		+	little specialized skils to construct.
		+
		+	Hi-res Photo:
		+	[[File:9088A.jpg\|left\|thumb]]
		+	.
		+
		+	As you can see, the card is perforated into 2 separate pieces.
		+
		+	One side (the "A" side) is an interface between the DMK URI
		+
		+	and the Kenwood TMG-707A. The other side (the "B" side) is an
		+
		+	interface between the 4 port PCI CARD and the
		+
		+	Kenwood TMG-707A.
		+
		+	Here is an example of a fully-constructed "A" side:
		+	[[File:9088-A.jpg\|left\|thumb\|9088-A Interface board]]
		+	.
		+
		+	It plugs directly into the end of the URI with the 25 pin connector,
		+
		+	and a serial port on your PC device with the 9 pin D-shell connector.
		+
		+	Here is an example of a fully-constructed "B" side:
		+	[[File:9088-B.jpg\|left\|thumb]]
		+	.
		+
		+	Its 8 pin modular jack goes to a shielded straight-thru modular
		+
		+	cable to a port on the 4 port PCI card.
		+
		+	Both sides use a 6 pin Male to Male mini-DIN cable with low profile
		+
		+	connectors, available from L-Com, to connect to the TMG-707A.
		+
		+	The Bill of Materials for the whole card (including DIGIKEY part
		+
		+	numbers may be accessed here.
		+
		+	Note: This Bill of Materials is for the BOTH halves of the board.
		+
		+	If you dont intend to use both halves, then dont buy the parts for
		+
		+	the half you dont want.
		+
		+	And for those who are interested here is the schematic.