MikroTik - Revision history

Kg7qin at 06:56, 24 January 2022

2022-01-24T06:56:14Z

2022-01-24T06:55:55Z

Added link to Mikrotik Wireguard Road Warrior Setup

2021-07-11T05:43:54Z

Installation

2021-07-11T00:00:39Z

Configuration

2021-07-10T23:58:55Z

Installation

2021-07-10T23:57:47Z

Installation

2021-07-10T23:32:07Z

Installation

2021-07-10T23:31:07Z

MikroTik CHR on VPS

2021-07-10T23:28:22Z

IPSEC

2021-07-10T23:24:52Z

Installation

@@ Line 1: / Line 1: @@
 [[Category: MikroTik]]
 __FORCETOC__
 Welcome to the MikroTik Wiki page.  Here you will find items specifically about using MikoTik devices and software as it relates to Ham Radio and/or AllStarLink/PTTLink.

← Older revision		Revision as of 06:55, 24 January 2022
Line 80:		Line 80:

	*[[VPN#strongSwan to MikroTik\|strongSwan to MikroTik]] - Information on connecting MikroTik to a system running the strongSwan IPSEC software		*[[VPN#strongSwan to MikroTik\|strongSwan to MikroTik]] - Information on connecting MikroTik to a system running the strongSwan IPSEC software
		+
		+	= Wireguard =
		+	The Mikrotik Wireguard Road Warrior Install is located at [[VPN#Mikrotik_Wireguard_Road_Warrior_Config\|Mikrotik Wireguard Road Warrior Setup]].

	= HamWAN =		= HamWAN =

@@ Line 35: / Line 35: @@
     gunzip -c chr.img.zip > chr.img && \
     mount -o loop,offset=33554944 chr.img /mnt && \
-    ADDRESS=`ip addr show ens3 | grep global | cut -d' ' -f 6 | head -n 1` && \
+    ADDRESS=`ip addr show '''''ens3''''' | grep global | cut -d' ' -f 6 | head -n 1` && \
     GATEWAY=`ip route list | grep default | cut -d' ' -f 3` && \
     echo "/ip address add address=$ADDRESS interface=[/interface ethernet find where name=ether1] /ip route add gateway=$GATEWAY " > /mnt/rw/autorun.scr && \
     umount /mnt && \
-    echo u > /proc/sysrq-trigger && \ dd if=chr.img bs=1024 of=/dev/vda
+    echo u > /proc/sysrq-trigger && \ dd if=chr.img bs=1024 of='''''/dev/vda'''''
 *Once you successfully complete the above, power off (do not shut down) the VPS and then turn it back on to boot into MikroTik CHR.

@@ Line 54: / Line 54: @@
 *If the above does not work on setting the IP address and gateway properly:
-**Set IP address with:  '''/ip addres interface=ether1 add address=<ip address> netmask=<netmask>'''
+**Set IP address with:  '''/ip address add address=<ip address> netmask=<netmask> interface=ether1'''
 **Set Gateway IP address with:  '''/ip route add dst-address=0.0.0.0/0 gateway=<gateway IP>'''

@@ Line 30: / Line 30: @@
     apt-get install unzip
-*Then copy and run the entire block of commands below into the terminal
+*Then copy and run the entire block of commands below into the terminal.  Verify the name of the interface in line 4 matches what your VPS uses.
     wget https://download.mikrotik.com/routeros/6.48.3/chr-6.48.3.img.zip -O chr.img.zip && \

← Older revision		Revision as of 23:57, 10 July 2021
Line 29:		Line 29:

	apt-get install unzip		apt-get install unzip
−
−	*Set '''$ADDRESS''' to the IP address the MikroTik CHR will use
−	*Set '''$GATEWAY''' to the IP address of the Gateway the MikroTik CHR will use
−
−	~~set ADDRESS="1.1.1.1"~~
−	~~set GATEWAY="2.2.2.2"~~

	*Then copy and run the entire block of commands below into the terminal		*Then copy and run the entire block of commands below into the terminal

@@ Line 33: / Line 33: @@
 *Set '''$GATEWAY''' to the IP address of the Gateway the MikroTik CHR will use
-    set $ADDRESS="1.1.1.1"
+    set ADDRESS="1.1.1.1"
-    set $GATEWAY="2.2.2.2"
+    set GATEWAY="2.2.2.2"
 *Then copy and run the entire block of commands below into the terminal

@@ Line 49: / Line 49: @@
 *Once you successfully complete the above, power off (do not shut down) the VPS and then turn it back on to boot into MikroTik CHR.
 *Login to the MikroTik CHR via the terminal using admin for the username with no password
 *Change the default admin password with:
     /user set name=admin password=<new password>
-== Configuration ==
+'''If the IP address and Gateway were not properly set at installation:'''
 Set $ADDRESS and $GATEWAY first or replace them in the line below with the actual values.
     echo "/ip address add address=$ADDRESS interface=[/interface ethernet find where name=ether1] /ip route add gateway=$GATEWAY"

@@ Line 81: / Line 81: @@
 = IPSEC =
-Sometimes you need to secure a link between a system and an MikroTik device.
+Sometimes you need to secure a link between a system and a MikroTik device.
 *[[VPN#strongSwan to MikroTik|strongSwan to MikroTik]] - Information on connecting MikroTik to a system running the strongSwan IPSEC software

@@ Line 31: / Line 31: @@
 *Set '''$ADDRESS''' to the IP address the MikroTik CHR will use
-*Set $GATEWAY to the IP address of the Gateway the MikroTik CHR will use
+*Set '''$GATEWAY''' to the IP address of the Gateway the MikroTik CHR will use
     set $ADDRESS="1.1.1.1"