Rpt.conf - Revision history

Kg7qin at 18:47, 27 January 2022

2022-01-27T18:47:28Z

Kg7qin at 18:47, 27 January 2022

2022-01-27T18:47:03Z

Kg7qin at 18:44, 27 January 2022

2022-01-27T18:44:34Z

Show changes

KM4NNO at 16:35, 1 January 2021

2021-01-01T16:35:49Z

Wd6awp: Added connpgm and discpgm

2019-12-18T19:46:36Z

Added connpgm and discpgm

Wd6awp: /* duplex= */

2019-06-16T18:14:53Z

duplex=

N8THN: /* Putting it all Together */

2019-01-28T15:26:12Z

Putting it all Together

N8THN: added telemdefault and telemdynamic

2019-01-28T15:20:37Z

added telemdefault and telemdynamic

N8THN: added guilinkdefault and guilinkdynamic

2019-01-28T15:14:42Z

added guilinkdefault and guilinkdynamic

N8THN: added other function definitions

2019-01-23T21:19:29Z

added other function definitions

@@ Line 1: / Line 1: @@
 [[Category:Node Configuration]]
 [[Category:Config Files]]
-Rpt.conf is where the majority of user-facing features, such as the node's CW and voice ID, DTMF commands and timers are set. There is a lot of capability here which can be difficult to grasp. Fortunately the default [https://github.com/pttlink/Asterisk/blob/master/allstar/configs/simpleusb/rpt.conf DIAL rpt.conf] is well commented and will work fine for most node admins.
+Rpt.conf is where the majority of user-facing features, such as the node's CW and voice ID, DTMF commands and timers are set. There is a lot of capability here which can be difficult to grasp. Fortunately the default [https://github.com/pttlink/Asterisk/blob/master/allstar/configs/simpleusb/rpt.conf Node rpt.conf] is well commented and will work fine for most node admins.
 =DTMF Commands=

@@ Line 1: / Line 1: @@
 [[Category:Node Configuration]]
 [[Category:Config Files]]
-Rpt.conf is where the majority of user-facing features, such as the node's CW and voice ID, DTMF commands and timers are set. There is a lot of capability here which can be difficult to grasp. Fortunately the default [https://github.com/PTTLink/DIAL/blob/master/configs/rpt.conf DIAL rpt.conf] is well commented and will work fine for most node admins.
+Rpt.conf is where the majority of user-facing features, such as the node's CW and voice ID, DTMF commands and timers are set. There is a lot of capability here which can be difficult to grasp. Fortunately the default [https://github.com/pttlink/Asterisk/blob/master/allstar/configs/simpleusb/rpt.conf DIAL rpt.conf] is well commented and will work fine for most node admins.
 =DTMF Commands=

@@ Line 1: / Line 1: @@
-Rpt.conf is where the majority of user-facing features, such as the node's CW and voice ID, DTMF commands and timers are set. There is a lot of capability here which can be difficult to grasp. Fortunately the default [https://github.com/AllStarLink/DIAL/blob/master/configs/rpt.conf DIAL rpt.conf] is well commented and will work fine for most node admins.
+Rpt.conf is where the majority of user-facing features, such as the node's CW and voice ID, DTMF commands and timers are set. There is a lot of capability here which can be difficult to grasp. Fortunately the default [https://github.com/PTTLink/DIAL/blob/master/configs/rpt.conf DIAL rpt.conf] is well commented and will work fine for most node admins.
 =DTMF Commands=
@@ Line 1,019: / Line 1,019: @@
 =Nodes Stanza=
-The [nodes] stanza is a list of nodes, their IP addresses, port and "NONE" for non-remote base nodes. The nodes stanza is used to identify which node is mapped to which Internet call and to determine the destination to send the call to. If you are using automatic update for Allstar link (public) nodes, no Allstar link nodes should be defined here. Only place a definition for your local nodes, and private (off of allstar link) nodes or nodes behind the same NAT router here.
+The [nodes] stanza is a list of nodes, their IP addresses, port and "NONE" for non-remote base nodes. The nodes stanza is used to identify which node is mapped to which Internet call and to determine the destination to send the call to. If you are using automatic update for PTTLink (public) nodes, no PTTLink nodes should be defined here. Only place a definition for your local nodes, and private (off of PTTLink) nodes or nodes behind the same NAT router here.
 Sample:
@@ Line 1,030: / Line 1,030: @@
 = radio@192.168.1.20:4570/2503,NONE       ; Public node behind the same NAT router
 </pre>
-The [nodes] stanza performs a function similar to an OS hosts file. When looking up node information, app_rpt looks in the [nodes] stanza first then searches (what could be called the Allstar DNS) the /var/lib/asterisk/rpt_extnodes file.
+The [nodes] stanza performs a function similar to an OS hosts file. When looking up node information, app_rpt looks in the [nodes] stanza first then searches (what could be called the PTTLink DNS) the /var/lib/asterisk/rpt_extnodes file.
 =Telemetry Stanza=

← Older revision		Revision as of 19:46, 18 December 2019
Line 381:		Line 381:

	''Note'': The value in quotes is the name of the autopatch caller, and the numbers in angle brackets are the originating telephone number to use.		''Note'': The value in quotes is the name of the autopatch caller, and the numbers in angle brackets are the originating telephone number to use.
		+
		+	==connpgm= and discpgm= ==
		+
		+	Runs user defined scripts. Example from https://www.qsl.net/k0kn/swissarmy_debian
		+	<pre>
		+	# Place these lines in rpt.conf for each node:
		+	# connpgm=/home/kyle/swissarmy 1
		+	# discpgm=/home/kyle/swissarmy 0
		+	</pre>

	==context===		==context===

@@ Line 415: / Line 415: @@
 | 2 || Full Duplex with telemetry tones and hang time. This mode is preferred when interfacing a repeater.
 |-
-| 3 || Full Duplex with telemetry tones and hang time, but no repeated audio.
+| 3 || Full Duplex with telemetry tones and hang time, but no repeated audio. [[Duplex Mode 3|See details]]
 |-
 | 4 || Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.

@@ Line 547: / Line 547: @@
 <pre>
 telemdynamic = 0 = disallow users to change the local telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command. Default is 1
 </pre>

@@ Line 537: / Line 537: @@
 <pre>
 holdofftelem = 1   ;Set to 1 to hold off. Default is 0
 </pre>

@@ Line 456: / Line 456: @@
 functions = functionsUHF   ; pointer to 440 repeater functions stanza
 </pre>
 = Function Classes =