Zoiper - Revision history

Kg7qin at 05:33, 28 January 2022

2022-01-28T05:33:12Z

Kg7qin: /* extensions.conf */

2021-07-14T05:02:47Z

extensions.conf

Kg7qin at 05:02, 14 July 2021

2021-07-14T05:02:07Z

Kg7qin at 04:59, 14 July 2021

2021-07-14T04:59:41Z

Kg7qin: Created initial page.

2021-07-14T04:59:17Z

Created initial page.

New page

Setting up your AllStarLink/PTTLink node to use Zoiper is simple!

==Node Configuration==
===iax.conf===
:Edit your '''/etc/asterisk/iax.conf''' file adding the following:

['''USERNAME'''] ; This stanza will be the same as your username from Zoiper
type=friend
context=sip-phone
username='''USERNAME''' ; Same as stanza above
auth=md5
secret='''PASSWORD''' ; Change to match the password you entered into Zoiper for the account
codecpriority=host
host=dynamic
disallow=all
allow=ulaw
allow=alaw
transfer=no
callerid='''CALLSIGN''' ; Change to your callsign

===extensions.conf===
:Edit your /etc/asterisk/extensions.conf file adding the following:

[iax-phone]
exten => '''NODE#''',1,Answer() ; Change NODE# to either match your node number of a number to connect to your node
exten => '''NODE#''',n,Set(CALLERID(name)="'''YOUR CALLSIGN'''")
exten => '''NODE#''',n,Playback(rpt/connected)
exten => '''NODE#''',n,PLayback(rpt/node)
exten => '''NODE#''',n,Saydigits(${EXTEN})
exten => '''NODE#''',n,Rpt(${EXTEN}|P|${CALLERID(name)})

==Zopier==
===Download===
You can download the latest version of Zoiper for Linux, Windows, Mac, Android, and iOS from https://www.zoiper.com/en/voip-softphone/download/current. The "classic" versions are available for download from https://www.zoiper.com/en/voip-softphone/download/classic

===Configuration===
You can find instructions for configuring Zoiper for use with a SIP/IAX2 account are located at [https://www.zoiper.com/en/support/home/article/192/How%20to%20set%20SIP%2FIAX2%20account%20with%20Zoiper Zoiper Setup].

Note: You want to use the '''IAX UDP''' account type.

===Calling===
*Start Zoiper
*Ensure Zopier is registering with your node using the account information you setup previously.
**In Zoiper: you will see a green check mark next to the account under '''''Settings->Accounts'''''
**In Asterisk: you can check your node to see if Zoiper has successfully registered with:
KG7QIN*CLI> iax2 show peers
Name/Username Host Mask Port Status
kg7qin/kg7qin 192.168.0.20 (D) 255.255.255.255 4569 Unmonitored

:Your account will show the IP address under Host for a successful registration or ''(Unspecified)'' if it hasn't

*Dial your NODE # (or the access number) you setup in extensions.conf and you will be greeted with "Connected node <NODE NUMBER>" and your node can then dial out to the AllStarLink/PTTLink network using * commands.

← Older revision		Revision as of 05:02, 14 July 2021
Line 1:		Line 1:
		+	[[Category:How to]]
		+	[[Category:Node Configuration]]
		+	[[Category:Software]]
	Setting up your AllStarLink/PTTLink node to use Zoiper is simple!		Setting up your AllStarLink/PTTLink node to use Zoiper is simple!

@@ Line 6: / Line 6: @@
 ==Node Configuration==
 ===iax.conf===
 :Edit your '''/etc/asterisk/iax.conf''' file adding the following:
-   ['''USERNAME''']  ; This stanza will be the same as your username from Zoiper
+<syntaxhighlight lang="ini">[<USERNAME>]         ; This stanza will be the same as your username from Zoiper
-   type=friend
+type=friend
-   context=sip-phone
+context=sip-phone
-   username='''USERNAME'''  ; Same as stanza above
+username=<USERNAME>  ; Same as stanza name above
-   auth=md5
+auth=md5
-   secret='''PASSWORD'''  ; Change to match the password you entered into Zoiper for the account
+secret=<PASSWORD>    ; Change to match the password you entered into Zoiper for the account
-   codecpriority=host
+codecpriority=host
-   host=dynamic
+host=dynamic
-   disallow=all
+disallow=all
-   allow=ulaw
+allow=ulaw
-   allow=alaw
+allow=alaw
-   transfer=no
+transfer=no
-   callerid='''CALLSIGN'''  ; Change to your callsign
+callerid=<CALLSIGN>  ; Change to your callsign</syntaxhighlight>
 ===extensions.conf===
 :Edit your '''/etc/asterisk/extensions.conf''' file adding the following:
-   [iax-phone]
+<syntaxhighlight lang="ini">[iax-phone]
-   exten => '''NODE#''',1,Answer() ; Change NODE# to either match your node number of a number to connect to your node
+exten => <NODE#>,1,Answer() ; Change NODE# to either match your node number of a number to connect to your node
-   exten => '''NODE#''',n,Set(CALLERID(name)="'''YOUR CALLSIGN'''")
+exten => <NODE#>,n,Set(CALLERID(name)="'''YOUR CALLSIGN'''")
-   exten => '''NODE#''',n,Playback(rpt/connected)
+exten => <NODE#>,n,Playback(rpt/connected)
-   exten => '''NODE#''',n,PLayback(rpt/node)
+exten => <NODE#>,n,PLayback(rpt/node)
-   exten => '''NODE#''',n,Saydigits(${EXTEN})
+exten => <NODE#>,n,Saydigits(${EXTEN})
-   exten => '''NODE#''',n,Rpt(${EXTEN}|P|${CALLERID(name)})
+exten => <NODE#>,n,Rpt(${EXTEN}|P|${CALLERID(name)})</syntaxhighlight>
 ==Zopier==