Search results
Jump to navigation
Jump to search
- Interfacing the GM300153 bytes (3 words) - 06:17, 6 September 2021
- This page discusses interfacing the Motorola Quantar to the RTCM/VOTER interface, for use with AllStar. This page should get you up and running with how18 KB (2,917 words) - 05:58, 28 January 2022
- Astro-TAC/RTCM Interface Cable Interfacing to a Quantar with P25Link and P25NX - Bryan Fields W9CR has page on interfacing the Qunatar using simple USB into PTTLink10 KB (1,238 words) - 17:13, 27 May 2022
- RTCM Client (redirect from RTCM/VOTER Interfaces)commercially available hardware for interfacing radios to an PTTLink computer. The Micro-Node RTCM and VOTER interfaces are typically used with PTTLink in57 KB (9,850 words) - 01:41, 15 March 2021
- Chan_usbradio is a feature rich DSP radio interface. It requires more CPU than chan_simpleusb and therefor chan_simpleusb may be a better choice on smaller5 KB (742 words) - 16:37, 1 January 2021
- addtap.bat netsh interface ipv4 show interfaces (Note disconnected interface. May be called Ethernet 2) netsh interface set interface name = "Ethernet70 KB (10,139 words) - 01:16, 23 February 2024
- meant to be used in conjunction with linktolink, inxlat, and outxlat when interfacing a radio port to a multiport analog repeater controller on an RF-linked42 KB (4,338 words) - 18:47, 27 January 2022
- needed for the interface. If the compiled in IP is matched, it will return a dump of the database. jsondata.cgi - not needed for the interface, used for returning2 KB (356 words) - 18:39, 5 August 2018
- This file sets up the app_rpt interface to an RTCM. The RTCM may be used in any of 3 modes; non-voting client mode, voting mode or voting and simulcast940 bytes (126 words) - 16:38, 1 January 2021
- use /etc/network/interfaces, and add DNS and the firewall to it and search in the allstarlink.org domain # The primary network interface auto eth0 iface14 KB (2,228 words) - 05:48, 24 January 2022
- you wish to support. For USB interfaces, more processor horsepower is necessary. If you are going to use a USB interface, then the CPU speed should ne14 KB (1,863 words) - 06:02, 28 January 2022
- The chan_voter channel driver is the interface between Asterisk and the RTCM/VOTER radio/repeater hardware interface. It allows receiver voting, simulcast16 KB (2,656 words) - 19:09, 31 March 2019
- default | cut -d' ' -f 3` && \ echo "/ip address add address=$ADDRESS interface=[/interface ethernet find where name=ether1] /ip route add gateway=$GATEWAY "6 KB (938 words) - 06:56, 24 January 2022
- a Virtual Machine in a data center. Multiple repeaters (nodes) may be interfaced at one site while only running one instance of Asterisk/app_rpt on one2 KB (332 words) - 06:26, 6 September 2021
- confuse the USB channel driver and require that usbradio.conf have all the interfaces removed or commented out and added back in one at a time. The use of USB3 KB (564 words) - 16:20, 1 January 2021
- AT93C46E-PU (Digikey Part Number AT93C46E-PU-ND) or equiv. to the URI via the interface connector, thereby allowing the USBRadio channel driver's working parameters872 bytes (170 words) - 03:10, 27 January 2019
- Whats Required (section Radio Interface)An assigned dedicated node number (e.g. pttlink.org) A radio interface A radio interface cable A supported radio A new or existing PC host computer Remote1 KB (195 words) - 16:22, 1 January 2021
- EEProm to save parameters, please see https://wiki.allstarlink.org/wiki/Interface_EPROM_to_URI Motorola Desktrac Repeater - Flat audio Tie Desktrac 20 and2 KB (401 words) - 03:31, 27 January 2019
- bryan@StPeteRpt:~ $ sudo dahdi_test [sudo] password for bryan: Opened pseudo dahdi interface, measuring accuracy... 99.614% 99.594% 99.608% 99.608% 98.476% 99.638%4 KB (638 words) - 17:09, 5 February 2022
- instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces. rxboost=1 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed6 KB (867 words) - 17:53, 27 January 2022