36
edits
Changes
Jump to navigation
Jump to search
Line 187:
Line 187: + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + +
no edit summary
=RTCM/VOTER LED's=
=RTCM/VOTER LED's=
RX LED on the RTCM/VOTER will flash (same rate as ACT LED) if you have External CTCSS enabled, and the received signal has the wrong (or no) valid PL.
RX LED on the RTCM/VOTER will flash (same rate as ACT LED) if you have External CTCSS enabled, and the received signal has the wrong (or no) valid PL.
=Menus=
==Main Menu==
This is what a typical Main Menu looks like:
<pre>
Select the following values to View/Modify:
1 - Serial # (0000) (which is MAC ADDR 00:04:A3:00:00:00)
2 - VOTER Server Address (FQDN) (44.128.1.1)
3 - VOTER Server Port (667), 4 - Local Port (Override) (0)
5 - Client Password (password1), 6 - Host Password (hostpass1)
7 - Tx Buffer Length (800)
8 - GPS Data Protocol (0=NMEA, 1=TSIP) (1)
9 - GPS Serial Polarity (0=Non-Inverted, 1=Inverted) (1)
10 - GPS PPS Polarity (0=Non-Inverted, 1=Inverted, 2=NONE) (0)
11 - GPS Baud Rate (9600)
12 - External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted) (0)
13 - COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver) (0)
14 - Debug Level (0)
15 - Alt. VOTER Server Address (FQDN) ()
16 - Alt. VOTER Server Port (Override) (0)
17 - DSP/BEW Mode (0)
18 - "Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs) (0)
19 - Simulcast Launch Delay (0) (approx 200 ns, 5 = 1us, > 0 to ENA SC)
97 - RX Level, 98 - Status, 99 - Save Values to EEPROM
i - IP Parameters menu, o - Offline Mode Parameters menu
q - Disconnect Remote Console Session, r - reboot system, d - diagnostics
Enter Selection (1-27,97-99,r,q,d) :
</pre>
==IP Parameters Menu==
This is what a typical IP Parameters Menu looks like:
<pre>
IP Parameters Menu
Select the following values to View/Modify:
1 - (Static) IP Address (44.128.1.2)
2 - (Static) Netmask (255.255.255.0)
3 - (Static) Gateway (44.128.1.254)
4 - (Static) Primary DNS Server (44.128.1.254)
5 - (Static) Secondary DNS Server (0.0.0.0)
6 - DHCP Enable (0)
7 - Telnet Port (23)
8 - Telnet Username (admin)
9 - Telnet Password (radios)
10 - DynDNS Enable (0)
11 - DynDNS Username (wb6nil)
12 - DynDNS Password (radios42)
13 - DynDNS Host (voter-test.dyndns.org)
14 - BootLoader IP Address (192.168.1.10) (OK)
15 - Ethernet Duplex (0=Half, 1=Full) (1)
99 - Save Values to EEPROM
x - Exit IP Parameters Menu (back to main menu)
q - Disconnect Remote Console Session, r - reboot system
Enter Selection (1-14,99,c,x,q,r) :
</pre>
==Offline Parameters Menu==
This is what a typical Offline Parameters Menu looks like:
<pre>
OffLine Mode Parameters Menu
Select the following values to View/Modify:
1 - Offline Mode (0=NONE, 1=Simplex, 2=Simplex w/Trigger, 3=Repeater) (3)
2 - CW Speed (400) (1/8000 secs)
3 - Pre-CW Delay (4000) (1/8000 secs)
4 - Post-CW Delay (4000) (1/8000 secs)
5 - CW "Offline" (ID) String (WB6NIL)
6 - CW "Online" String (OK)
7 - "Offline" (CW ID) Period Time (6000) (1/10 secs)
8 - Offline Repeat Hang Time (15) (1/10 secs)
9 - Offline CTCSS Tone (0.0) Hz
10 - Offline CTCSS Level (0-32767) (3000)
11 - Offline De-Emphasis Override (0=NORMAL, 1=OVERRIDE) (0)
99 - Save Values to EEPROM
x - Exit OffLine Mode Parameter Menu (back to main menu)
q - Disconnect Remote Console Session, r - reboot system
Enter Selection (1-9,99,c,x,q,r) :
</pre>