Difference between revisions of "Rpt.conf"

From "PTTLink Wiki"
Jump to navigation Jump to search
m
 
(257 intermediate revisions by 6 users not shown)
Line 1: Line 1:
Rpt.conf is where the majority of the node configuration occurs. Important node settings such as the node CW and voice ID, touchtone commands and timers are set. The default DIAL rpt.conf is well commented (see [https://github.com/AllStarLink/DIAL/blob/master/configs/rpt.conf rpt.conf on GitHub]).  
+
[[Category:Node Configuration]]
 +
[[Category:Config Files]]
 +
Rpt.conf is where the majority of user-facing features, such as the node's CW and voice ID, DTMF commands and timers are set. There is a lot of capability here which can be difficult to grasp. Fortunately the default [https://github.com/pttlink/Asterisk/blob/master/allstar/configs/simpleusb/rpt.conf Node rpt.conf] is well commented and will work fine for most node admins.
  
=Node Number Stanza=
+
=DTMF Commands=
The node number stanza is the first stanza in rpt.conf.  
+
DTMF commands are placed in any one of three [[Structure of Config Files|named stanzas]]. Function stanzas control access to DTMF commands that a user can issue from various
 +
control points.
 +
* The [[#Functions Stanza|fuctions stanza]] - to decode DTMF from the node's local receiver.
 +
* The [[#Link Functions Stanza|link_functions stanza]] - to decode DTMF from linked nodes.
 +
* The [[#Phone Functions Stanza|phone_functions stanza]] - to decode DTMF from telephone connects.
 +
 +
A function stanza key/value pair has the following format:
  
<pre>
+
dtmfcommand=functionclass,[functionmethod],[parameters]
[1999]   ; Replace with your assigned node number
+
Where:
</pre>
+
* dtmfcommand is a DTMF digit sequence '''minus''' the [[#funcchar=|start character]] (usually *)
 +
* functionclass is a string which defines what class of command; link, status or COP
 +
* functionmethod defines the optional method number to use in the function class.
 +
* functionoptions are one or more optional comma separated parameters which further define a command.
  
The node number stanza contains following key/value pairs.
+
==Status Commands==
==althangtime===
+
Status commands (functioncalss 'status') provide general information about the node.  
This controls the length of the repeater hang time when the alternate hang timer is selected with a control operator function. It is specified in milliseconds.
 
 
 
Sample:
 
<pre>
 
althangtime=4000  ; 4 seconds
 
</pre>
 
==beaconing===
 
When set to 1 will send the repeater ID at the idtime interval regardless of whether there was repeater activity or not. This feature appears to be required in the UK, but is probably illegal in the US.
 
 
 
Sample:
 
<pre>
 
beaconing=1  ;Set to 1 to beacon. Defaults to 0
 
</pre>
 
==callerid===
 
This setting allows the autopatch on the node to be identified with a specific caller ID. The default setting is as follows
 
 
 
<pre>
 
callerid="Repeater" <0000000000>
 
</pre>
 
 
 
''Note'': The value in quotes is the name of the autopatch caller, and the numbers in angle brackets are the originating telephone number to use.
 
 
 
==context===
 
 
 
This setting directs the autopatch for the node to use a specific context in extensions.conf for outgoing autopatch calls. The default is to specify a context name of radio.
 
  
<pre>
+
<syntaxhighlight lang="ini">712 = status,12  ; Give Time of Day (local only)</syntaxhighlight>
context=radio
 
</pre>
 
 
 
==rxchannel===
 
The rxchannel key/value pair selects the radio interface. There must be only one rxchannel per node. The selections are:
 
  
 
{| class="wikitable"
 
{| class="wikitable"
! Value !! Description  
+
! Status !! Description
|-  
+
|-
| dahdi/pseudo || No radio, used for hubs
+
| 1 || Force ID (global)
|-  
+
|-
| SimpleUSB/usb_1999 || SimpleUSB (limited DSP)  
+
| 2 || Give Time of Day (global)
|-  
+
|-
| Radio/usb_1999 || USBRadio (full DSP)  
+
| 3 || Give software Version (global)
|-  
+
|-
| voter/1990 || RTCM
+
| 4 || Give GPS location info
|-  
+
|-
| Pi/1 || Raspberry Pi PiTA
+
| 5 || Speak the last (dtmf) user
|-  
+
|-
| Dahdi/1 || PCI Quad card
+
| 11 || Force ID (local only)
|-
+
|-
| Beagle/1 || BeagleBoard
+
| 12 || Give Time of Day (local only)
|-  
 
| USRP/127.0.0.1:34001:32001 || GNU Radio interface USRP
 
 
|}
 
|}
Sample:
 
<pre>
 
rxchannel = dahdi/pseudo    ; No radio (hub)
 
</pre>
 
 
''Note'': This is selecting what is known as (in Asterisk terminology) the channel driver.
 
 
==controlstates===
 
This setting defines the name of the [[Structure of Config Files|variable named]] control state stanza. Control states are an optional feature which allows groups of control operator commands to be executed all at once. To use control states, define an entry in your node stanzas to point to a dedicated control state stanza like this:
 
<pre>
 
controlstates = controlstates  ; points to control state stanza
 
  
[controlstates]
+
==Link Commands==
0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation                                 
+
Link commands (functioncalss 'link') connect to, disconnect from, monitor (Rx only) other nodes and give link status.
1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation                                           
 
2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation
 
</pre>
 
  
The [[#Control States Stanza|control state stanza]] (below) describes these mnemonics.
+
<syntaxhighlight lang="ini">3 = ilink,3  ; Connect specified link -- transceive</syntaxhighlight>
  
==duplex===
 
The duplex key/value pairs sets the duplex mode for desired radio operation. Duplex mode 2 is the default if none specified.
 
 
{| class="wikitable"
 
{| class="wikitable"
! Duplex Mode !! Description  
+
! ilink !! Description
|-  
+
|-
| 0 || Half duplex with no telemetry tones or hang time. Special Case: Full duplex if linktolink is set to yes. This mode is preferred when interfacing with an external multiport repeater controller. Comment out idrecording and idtalkover to suppress IDs.
+
| 1 || Disconnect specified link
 +
|-
 +
| 2 || Connect specified link -- monitor only
 +
|-
 +
| 3 || Connect specified link -- tranceive
 +
|-
 +
| 4 || Enter command mode on specified link
 +
|-
 +
| 5 || System status
 +
|-
 +
| 6 || Disconnect all links
 +
|-
 +
| 7 || Last Node to Key Up
 +
|-
 +
| 8 || Connect specified link -- local monitor only
 
|-
 
|-
| 1 || Half duplex with telemetry tones and hang time. Does not repeat audio. This mode is preferred when interfacing a simplex node.
+
| 9 || Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.
 
|-
 
|-
| 2 || Full Duplex with telemetry tones and hang time. This mode is preferred when interfacing a repeater.
+
| 10 || Disconnect all RANGER links (except permalinks)
|-
 
| 3 || Full Duplex with telemetry tones and hang time, but no repeated audio.
 
|-
 
| 4 || Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.
 
|}
 
 
 
Sample:
 
<pre>
 
duplex = 0    ; 0 = Half duplex with no telemetry tones or hang time.
 
</pre>
 
 
 
=Functions Stanza=
 
 
 
==Status Commands==
 
Status commands provide general information about the node.
 
{| class="wikitable"
 
! Status !! Status Function
 
 
|-
 
|-
| 1 || Force ID (global)
+
| 11 || Disconnect a previously permanently connected link
 
|-
 
|-
| 2 || Give Time of Day (global)
+
| 12 || Permanently connect specified link -- monitor only
 
|-
 
|-
| 3 || Give software Version (global)
+
| 13 || Permanently connect specified link -- tranceive
 
|-
 
|-
| 4 || Give GPS location info
+
| 15 || Full system status (all nodes)
 
|-
 
|-
| 5 || Speak the last (dtmf) user
+
| 16 || Reconnect links disconnected with "disconnect all links"
 
|-
 
|-
| 11 || Force ID (local only)
+
| 17 || MDC test (for diag purposes)
 
|-
 
|-
| 12 || Give Time of Day (local only)
+
| 18 || Permanently Connect specified link -- local monitor only
 
|}
 
|}
  
 
==COP Commands==
 
==COP Commands==
COP (control operator) commands are privileged commands. Node admins may provide some of these to their user community based on personal preference. COP commands within rpt.conf take the general format of [[Structure of Config Files|key/value pairs]]. This COP 7 example would set touchtone *99 to enable the timeout timer.
+
Control operator (functionclass 'cop') commands are privileged commands. Node admins may provide some of these to their user community based on personal preference.  
  
<pre>99 = cop,7</pre>
+
<syntaxhighlight lang="ini">99 = cop,7   ; enable timeout timer</syntaxhighlight>
  
 
Some COP commands can take multiple parameters. For example this COP 48 would send #3#607 on command.
 
Some COP commands can take multiple parameters. For example this COP 48 would send #3#607 on command.
  
<pre>900=cop,48,#,3,#,6,0,7</pre>  
+
<syntaxhighlight lang="ini">900 = cop,48,#,3,#,6,0,7</syntaxhighlight>
  
 
{| class="wikitable"
 
{| class="wikitable"
 
|-
 
|-
! COP !! COP Function
+
! COP !! Description
 
|-
 
|-
 
|  1  || System warm boot
 
|  1  || System warm boot
Line 271: Line 231:
 
|-
 
|-
 
|  65 || Send POCSAG page (equipped channel types only)
 
|  65 || Send POCSAG page (equipped channel types only)
 +
|}
 +
 +
==Remote Base Commands==
 +
Remote base commands (functionclass 'remote') provide remote base control. This stanza is [[Structure of Config Files#Settings to name other Stanzas|named by]] the remote base [[#Remote Base Functions=|Remote Base Functions]] key/value pair.
  
 +
{| class="wikitable"
 +
! remote !! Description
 +
|-
 +
| 1 || Retrieve Memory
 +
|-
 +
| 2 || Set freq.
 +
|-
 +
| 3 || Set tx PL tone
 +
|-
 +
| 4 || Set rx PL tone
 +
|-
 +
| 5 || Long status query
 +
|-
 +
| 99,CALLSIGN,LICENSETAG || Remote Base login
 +
|-
 +
| 100 || Rx PL off
 +
|-
 +
| 101 || Rx PL on
 +
|-
 +
| 102 || Tx PL off
 +
|-
 +
| 103 || Tx PL on
 +
|-
 +
| 104 || Low Power
 +
|-
 +
| 105 || Medium Power
 +
|-
 +
| 106 || High Power
 +
|-
 +
| 107 || Bump -20
 +
|-
 +
| 108 || Bump -100
 +
|-
 +
| 109 || Bump -500
 +
|-
 +
| 110 || Bump +20
 +
|-
 +
| 111 || Bump +100
 +
|-
 +
| 112 || Bump +500
 +
|-
 +
| 113 || Scan - slow
 +
|-
 +
| 114 || Scan - quick
 +
|-
 +
| 115 || Scan - fast
 +
|-
 +
| 116 || Scan + slow
 +
|-
 +
| 117 || Scan + quick
 +
|-
 +
| 118 || Scan + fast
 +
|-
 +
| 119 || Tune
 +
|-
 +
| 140 || Short status query
 +
|-
 +
| 210 || Send a *
 +
|-
 +
| 211 || Send a #
 
|}
 
|}
  
==Linking Commands==
+
Not all commands above are supported by all radios. For example radios which don't support SSB, would not be able to be placed in LSB or USB mode.
 +
 
 +
===Remote Base Login===
 +
When [[#authlevel=|authlevel=]] is greater than zero, remote 99 is used to define a different dtmf sequence for each user authorized to use the remote base. The remote base will announce the callsign as access is granted.
 +
 
 +
<syntaxhighlight lang="ini">
 +
[remote node#]
 +
authlevel = 2 ; Remote base authentication level
 +
; authlevel = 0 : Anyone can use it
 +
; authlevel = 1 : Requires log in, Waits for Tx key to ask for it
 +
; authlevel = 2 : Requires log in, asks for it automously
 +
 
 +
[remote-functions]
 +
8xx=remote,99,OK,E ; password
 +
</syntaxhighlight>
 +
<syntaxhighlight lang="ini">
 +
9139583 = remote,99,WB6NIL,G  ; grant access to Jim (general)
 +
9148351 = remote,99,WA6ZFT,E  ; grant access to Steve (extra)
 +
</syntaxhighlight>
 +
When the remote base is disconnected from the originating node, the
 +
user will be logged out.
  
==Remote Base Commands==
+
The LICENSETAG argument is used to enforce
 +
tx frequency limits. Need info [txlimits].
 +
 
 +
= Settings to name other Stanzas =
 +
Within the node stanza, some key=value pairs point to other stanzas. This allows nodes on the same Asterisk/app_rpt server to have the same settings (without duplicate entries) or different settings in some cases. For example the phone patch command may be *6 on one node, yet *61 on another.
 +
 
 +
For example:
 +
<syntaxhighlight lang="ini">
 +
[1000]
 +
functions=functionsVHF
 +
 
 +
[1001]
 +
functions=functionsVHF
 +
 
 +
[1002]
 +
functions=functionsUHF
 +
 
 +
[functionsVHF]
 +
; Two meter Autopatch up is *6
 +
6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000
 +
0=autopatchdn      ; Autopatch down
 +
 
 +
[functionsUHF]
 +
; 440 Autopatch up is *61
 +
61=autopatchup,noct=1,farenddisconnect=1,dialtime=20000  ; Autopatch up
 +
0=autopatchdn      ; Autopatch down
 +
* controlstates=
 +
* functions=
 +
* link_functions=
 +
* macro=
 +
* phone_functions=
 +
* telemetry=
 +
* wait_times=
 +
</syntaxhighlight>
 +
 
 +
=Node Number Stanza=
 +
The node number stanza is the first stanza in rpt.conf.
 +
 
 +
<syntaxhighlight lang="ini">[1999]    ; Replace with your assigned node number</syntaxhighlight>
 +
 
 +
The node number stanza contains the following key/value pairs.
 +
==althangtime===
 +
This controls the length of the repeater hang time when the alternate hang timer is selected with a control operator function. It is specified in milliseconds.
 +
 
 +
<syntaxhighlight lang="ini">althangtime=4000  ; 4 seconds</syntaxhighlight>
 +
 
 +
==beaconing===
 +
When set to 1 will send the repeater ID at the idtime interval regardless of whether there was repeater activity or not. This feature appears to be required in the UK, but is probably illegal in the US.
 +
 
 +
<syntaxhighlight lang="ini">beaconing=1  ;Set to 1 to beacon. Defaults to 0</syntaxhighlight>
 +
 
 +
==callerid===
 +
This setting allows the autopatch on the node to be identified with a specific caller ID. The default setting is as follows
 +
<syntaxhighlight lang="ini">callerid="Repeater" <0000000000></syntaxhighlight>
 +
 
 +
''Note'': The value in quotes is the name of the autopatch caller, and the numbers in angle brackets are the originating telephone number to use.
 +
 
 +
==connpgm= and discpgm= ==
 +
 
 +
Runs user defined scripts. Example from https://www.qsl.net/k0kn/swissarmy_debian
 +
<syntaxhighlight lang="ini">
 +
# Place these lines in rpt.conf for each node:
 +
#    connpgm=/home/kyle/swissarmy 1
 +
#    discpgm=/home/kyle/swissarmy 0
 +
</syntaxhighlight>
 +
 
 +
==context===
 +
 
 +
This setting directs the autopatch for the node to use a specific context in extensions.conf for outgoing autopatch calls. The default is to specify a context name of radio.
 +
<syntaxhighlight lang="ini">context=radio</syntaxhighlight>
 +
 
 +
==controlstates===
 +
This setting defines the name of the [[Structure of Config Files|variable named]] control state stanza. Control states are an optional feature which allows groups of control operator commands to be executed all at once. To use control states, define an entry in your node stanzas to point to a dedicated control state stanza like this:
 +
<syntaxhighlight lang="ini">controlstates = controlstates  ; points to control state stanza</syntaxhighlight>
 +
 
 +
<syntaxhighlight lang="ini">
 +
[controlstates]
 +
0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation                                 
 +
1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation                                           
 +
2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation
 +
</syntaxhighlight>
 +
 
 +
The [[#Control States Stanza|control state stanza]] describes these mnemonics.
 +
 
 +
==duplex===
 +
The duplex key/value pairs sets the duplex mode for desired radio operation. Duplex mode 2 is the default if none specified.
 +
{| class="wikitable"
 +
! Duplex Mode !! Description
 +
|-
 +
| 0 || Half duplex with no telemetry tones or hang time. Special Case: Full duplex if linktolink is set to yes. This mode is preferred when interfacing with an external multiport repeater controller. Comment out idrecording and idtalkover to suppress IDs.
 +
|-
 +
| 1 || Half duplex with telemetry tones and hang time. Does not repeat audio. This mode is preferred when interfacing a simplex node.
 +
|-
 +
| 2 || Full Duplex with telemetry tones and hang time. This mode is preferred when interfacing a repeater.
 +
|-
 +
| 3 || Full Duplex with telemetry tones and hang time, but no repeated audio. [[Duplex Mode 3|See details]]
 +
|-
 +
| 4 || Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.
 +
|}
 +
 
 +
<syntaxhighlight lang="ini>
 +
duplex = 0    ; 0 = Half duplex with no telemetry tones or hang time.
 +
</syntaxhighlight>
 +
 
 +
==endchar===
 +
This setting allows the end character used by some control functions to be changed. By default this is a #. The endchar value must not be the same as the funcchar default or overridden value.
 +
 
 +
==erxgain===
 +
Echolink receive gain adjustment in +/- db-volts. Used to balance Echolink recieve audio on an app_rpt node.
 +
<syntaxhighlight lang="ini">erxgain = -3</syntaxhighlight>
 +
 
 +
See [[:Category:How to|Echolink How to]]
 +
 
 +
==etxgain===
 +
Echolink transmit gain adjustment in +/- db-volts. Used to balance Echolink transmit audio on an app_rpt node.
 +
<syntaxhighlight lang="ini">etxgain = 3</syntaxhighlight>
 +
 
 +
See [[:Category:How to|Echolink How to]]
 +
 
 +
==funcchar===
 +
This setting can be used to change the default function starting character of * to something else. Please note that the new value chosen must not be the same as the default or overridden value for endchar=.
 +
 
 +
==functions===
 +
This [[Structure of Config Files#Settings to name other Stanzas|names (points to)]] the [[#Functions Stanza|function stanza]].
 +
 
 +
<syntaxhighlight lang="ini">functions = functionsUHF  ; pointer to 440 repeater functions stanza</syntaxhighlight>
 +
 
 +
== GUI ==
 +
{| class="wikitable"
 +
!Key
 +
!Valid Values
 +
!Default
 +
|-
 +
|guilinkdefault
 +
|0 = telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode
 +
|1
 +
|-
 +
|guilinkdynamic
 +
|0 = disallow users to change the gui telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command
 +
|1
 +
|}
 +
 
 +
= Function Classes =
 +
Function classes are names for categories of functions. There are several function classes defined. They are described in the table below:
 +
{| class="wikitable"
 +
!Class
 +
!Description
 +
|-
 +
|cop
 +
|Control operator commands
 +
|-
 +
|ilink
 +
|Internet linking commands
 +
|-
 +
|status
 +
|User Status Commands
 +
|-
 +
|autopatchup
 +
|Autopatch up commands
 +
|-
 +
|autopatchdn
 +
|Autopatch down commands
 +
|-
 +
|remote
 +
|Remote base commands
 +
|-
 +
|macro
 +
|Command Macros
 +
|}
 +
Most of the above command classes require a function method and possibly one or more additional command parameters. Function methods are discussed next.
 +
 
 +
= Function Methods =
 +
Function methods are numbers which identify a specific function to execute within a function class. Function Methods are optional and in some cases should be omitted (Such as with the autopatchup method) A complete and up-to-date description of all functon methods can be found in the app_rpt.c source file. Some function methods are shown below as an example below:
 +
1  - Force ID (global)
 +
2  - Give Time of Day (global)
 +
3  - Give software Version (global)
 +
11 - Force ID (local only)
 +
12 - Give Time of Day (local only)
 +
 
 +
= Function Options =
 +
Some Function Methods can take function options. These are specified after the Function Method separated with commas. Not all commands require or take Function options. An example of a method which can accept Function Options is the autopatchup method.
 +
 
 +
= Putting it all Together =
 +
A small excerpt from the function stanza of rpt.conf is hown below.
 +
<syntaxhighlight lang="ini">
 +
[functions]
 +
1=ilink,1                                              ; Specific link disconnect
 +
6=autopatchup,noct=1,farenddisconnect=1,dialtime=2000  ; Autopatch up
 +
</syntaxhighlight>
 +
The above example contains DTMF functions with all of the parameters discussed on previous pages.
 +
 
 +
In the above example:
 +
* *1 followed by a node number disconnects a specific link. The function class is ''ilink'' and the function method is ''1''
 +
* *6 followed by a phone number brings up the autopatch with the function options specified. Note that there is no function method defined, but there are function options present.
 +
 
 +
==hangtime===
 +
This controls the length of the repeater hang time. It is specified in milliseconds.
 +
 
 +
<syntaxhighlight lang="ini">hangtime = 1000  ;Set hang time for 1 second</syntaxhighlight>
 +
 
 +
==holdofftelem===
 +
This node stanza configuration key forces all telemetry to be held off until a local user on the receiver or a remote user over a link unkeys. There is one exception to this behavior: When an ID needs to be sent and there is activity coming from a linked node.
 +
 
 +
<syntaxhighlight lang="ini">holdofftelem = 1  ;Set to 1 to hold off. Default is 0</syntaxhighlight>
 +
 
 +
== telemdefault= ==
 +
<syntaxhighlight lang="ini">telemdefault =  0 = telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter. Default is 1</syntaxhighlight>
 +
 
 +
== telemdynamic= ==
 +
<syntaxhighlight lang="ini">telemdynamic = 0 = disallow users to change the local telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command. Default is 1</syntaxhighlight>
 +
 
 +
== phonelinkdefault= ==
 +
<syntaxhighlight lang="ini">phonelinkdefault = 0 = telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode  Default is 1</syntaxhighlight>
 +
 
 +
== phonelinkdynamic= ==
 +
<syntaxhighlight lang="ini">phonelinkdynamic = 0 = disallow users to change phone telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command  Default is 1</syntaxhighlight>
 +
 
 +
==idrecording===
 +
The identifier message is stored in the node stanza using the idrecording key. It can be changed to a different call sign by changing the value to something different. The value can be either a morse code identification string prefixed with |i, or the name of a sound file containing a voice identification message. When using a sound file, the default path for the sound file is /var/lib/asterisk/sounds.
 +
 
 +
<syntaxhighlight lang="ini">idrecording = |iwa6zft/r  ; Morse Code ID</syntaxhighlight>
 +
or
 +
<syntaxhighlight lang="ini">idrecording = /var/lib/asterisk/sounds/myid  ; Voice ID</syntaxhighlight>
 +
''Note'': ID recording files must have extension gsm,ulaw,pcm, or wav. The extension is left off when it is defined as the example shows above. File extensions are used by Asterisk to determine how to decode the file. All ID recording files should be sampled at 8KHz. See [[Recording Audio Files|Recording audio files]]
 +
 
 +
==idtalkover===
 +
The ID talkover message is stored in the node stanza using the idtalkover setting. The purpose of idtalkover is to specify an alternate ID to use when the ID must be sent over the top of a user transmission, This can be a shorter voice ID or an ID in morse code. The value can be either a morse code identification string prefixed with |i, or the name of a sound file containing a voice identification message. When using a sound file, the default path for the sound file is /var/lib/asterisk/sounds. Example usages are as follows:
 +
 
 +
<syntaxhighlight lang="ini">idtalkover = |iwa6zft/r  ; Morse Code ID</syntaxhighlight>
 +
or
 +
<syntaxhighlight lang="ini">idtalkover = /var/lib/asterisk/sounds/myid  ; Voice ID</syntaxhighlight>
 +
''Note'': ID recording files must have extension gsm,ulaw,pcm, or wav. The extension is left off when it is defined as the example shows above. File extensions are used by Asterisk to determine how to decode the file. All ID recording files should be sampled at 8KHz. See [[Recording Audio Files|Recording audio files]]
 +
 
 +
==inxlat===
 +
The inxlat setting allows complete remapping of the funcchar and endchar digits to different digits or digit sequences.
 +
inxlat acts on the digits received by the radio receiver on the node.
 +
 
 +
Format: inxlat = funchars,endchars,passchars,dialtone
 +
 
 +
where:
 +
 
 +
* funcchars is the digit or digit sequence to replace funcchar
 +
* endchars is the digit or digit sequence to replace endchar
 +
* passchars are the digits to pass through (can be used to block certain digits)
 +
* dialtone is optional. Set to Y for dial tone on successful funcchars.
 +
 
 +
<syntaxhighlight lang="ini">inxlat = #56,#57,0123456789ABCD ; string xlat from radio port to sys</syntaxhighlight>
 +
 
 +
==link_functions===
 +
This [[Structure of Config Files#Settings to name other Stanzas|names (points to)]] the link_functions stanza.
 +
 
 +
The link_functions setting directs the node to use a particular function stanza for functions dialed by users accessing the node via a link from another node. The traditional default is to point it to a function stanza named "functions".
 +
 
 +
<syntaxhighlight lang="ini">link_functions = functions ; pointer to the Link Function stanza</syntaxhighlight>
 +
 
 +
==linkmongain===
 +
Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. If linkmongain set to a positive number monitored audio will increase by the set amount in db. The value of linkmongain is in db. The default value is 0 db.
 +
 
 +
<syntaxhighlight lang="ini">linkmongain = -20  ; reduce link volume 20dB</syntaxhighlight>
 +
 
 +
==linktolink===
 +
When operating in duplex mode 0, this forces the radio interface to operate in full duplex mode, but keeps all the other duplex mode 0 semantics. This is used when a radio interface is connected to a multiport analog repeater controller. The linktolink= key can take two values: yes or no.
 +
 
 +
<syntaxhighlight lang="ini">linktolink = yes  ; set to yes to enable. Default is no.</syntaxhighlight>
 +
 
 +
==linkunkeyct===
 +
The linkunkeyct setting selects the courtesy tone to send when a connected remote node unkeys. The default is no courtesy tone when a remote node unkeys.
 +
 
 +
<syntaxhighlight lang="ini">linkunkeyct = ct8  ; use courtesy tone 8</syntaxhighlight>
 +
 
 +
==macro===
 +
The marco key/value points to by the [[#Macro Stanza|Macro Stanza]] key/value pair. Macros are DTMF shortcuts.
 +
 
 +
<syntaxhighlight lang="ini">macro=macro  ; use stanza names 'macros'
 +
 
 +
[macro]
 +
1 = *32000*32001    ; connect to nodes 2000 and 2001
 +
</syntaxhighlight>
 +
 
 +
==nounkeyct===
 +
The nounkeyct node stanza key completely disables the courtesy tone. This is useful for eliminating TX time in applications using simplex uplinks to repeaters on the repeater pair itself.  This practice is '''strongly''' discouraged.
 +
 
 +
<syntaxhighlight lang="ini">nounkeyct = yes  ; :(</syntaxhighlight>
 +
 
 +
==politeid===
 +
The politeid setting specified the number of milliseconds prior to the end of the id cycle where the controller will attempt to play the ID in the tail when a user unkeys. If the controller does not get a chance to send the ID in the tail, the ID will be played over the top of the user transmission. Optional, default 30000.
 +
 
 +
<syntaxhighlight lang="ini">politeid = 30000  ; 30 seconds</syntaxhighlight>
 +
 
 +
==propagate_dtmf===
 +
Takes either yes or no. When set to yes, DTMF will be regenerated from out-of-band signalling or from from the receiver dtmf decoder whenever a function start character is NOT detected and command decoding has not begun. When set to no, no tones will be regenerated. The default for this setting is no.
 +
This setting is meant to be used in conjunction with linktolink, inxlat, and outxlat when interfacing a radio port to a multiport analog repeater controller on an RF-linked system.
 +
 
 +
<syntaxhighlight lang="ini">propagate_dtmf = no</syntaxhighlight>
 +
''Note'': There is a separate setting propagate_phonedtmf for use by dial-in (phone and dphone) users.
 +
 
 +
==remotect===
 +
The remotect setting allows the selection of the remote linked courtesy tone so that the users can tell there is a [[:Category:Remote Base|remote base]] connected locally.
 +
 
 +
<syntaxhighlight lang="ini">remotect = ct3  ; use courtesy tone 3</syntaxhighlight>
 +
 
 +
==rxburstfreq===
 +
If rx tone burst operation is desired, specify the frequency in hertz of the desired tone burst. Setting to 0 (or not specifying) indicates no tone burst operation.
 +
 
 +
<syntaxhighlight lang="ini">rxburstfreq = 1000</syntaxhighlight>
 +
 
 +
==rxburstthreshold===
 +
In rx toneburst mode, specifies the minimum signal to noise ratio in db that qualifies a valid tone.
 +
Defaults to 16 (db).
 +
 
 +
==rxbursttime===
 +
For rx toneburst operation, specifies minimum amount of time that tone needs to be valid for recognition (in milliseconds). Defaults to 250.
 +
 
 +
==rxchannel===
 +
The rxchannel key/value pair selects the radio interface. There must be one (and only one) rxchannel per node. The selections are:
 +
 
 +
{| class="wikitable"
 +
! Value !! Description
 +
|-
 +
| dahdi/pseudo || No radio, used for hubs
 +
|-
 +
| SimpleUSB/usb_1999 || [[SimpleUSB_Channel_Driver|SimpleUSB (limited DSP)]]
 +
|-
 +
| Radio/usb_1999 || [[Usbradio.conf|USBRadio (full DSP)]]
 +
|-
 +
| voter/1990 || [[Voter.conf|RTCM]]
 +
|-
 +
| Pi/1 || Raspberry Pi PiTA
 +
|-
 +
| Dahdi/1 || PCI Quad card
 +
|-
 +
| Beagle/1 || BeagleBoard
 +
|-
 +
| USRP/127.0.0.1:34001:32001 || GNU Radio interface USRP
 +
|}
 +
<syntaxhighlight lang="ini">rxchannel = dahdi/pseudo    ; No radio (hub)</syntaxhighlight>
 +
 
 +
''Note'': This is selecting what is known as (in Asterisk terminology) the channel driver.
 +
 
 +
==scheduler===
 +
This setting defines the scheduler stanza. The scheduler is used to execute commands at a particular time.
 +
 
 +
<syntaxhighlight lang="ini">scheduler = schedule  ; name scheduler to 'schedule'
 +
 
 +
[schedule]
 +
...
 +
</syntaxhighlight>
 +
 
 +
==sleeptime===
 +
This sets the inactivity period in seconds for no signal on the repeater receiver before the system goes to sleep.
 +
 
 +
<syntaxhighlight lang="ini">sleeptime = 300  ; go to sleep after 5 mins of no activity</syntaxhighlight>
 +
 
 +
==startup_macro===
 +
The startup_macro is executed once on system startup. Each node can have one startup macro defined in its node stanza.
 +
 
 +
<syntaxhighlight lang="ini">startup_macro = *31000 *31001 *31002  ; Connect to 1000, 1001 and 1002 at startup</syntaxhighlight>
 +
 
 +
One string of one or multiple commands executed in order.
 +
Note that this line of commands does NOT terminate with a # like a normal macro. And you can call any number of regular macros with it.
 +
 
 +
==tailmessagelist===
 +
The tailmessagelist setting allows a comma separated list of audio files to be specified for the tail message function. The tail messages will rotate from one to the next until the end of the list is reached at which point the first message in the list will be selected. If no absolute path name is specified, the directory var/lib/asterisk/sounds will be searched for the sound file. The file extension should be omitted.
 +
 
 +
<syntaxhighlight lang="ini">tailmessagelist = welcome,clubmeeting,wx  ; rotate 3 tail messages</syntaxhighlight>
 +
 
 +
''Note'': ID recording files must have extension gsm,ulaw,pcm, or wav. The extension is left off when it is defined as the example shows above. File extensions are used by Asterisk to determine how to decode the file. All ID recording files should be sampled at 8KHz. See [[Recording Audio Files|Recording audio files]]
 +
 
 +
==tailmessagetime===
 +
This sets the amount of time in milliseconds between tail messages. Tail Messages are played when a user unkeys on the repeater input at the point where the hang timer expires after the courtesy tone is sent.
 +
 
 +
<syntaxhighlight lang="ini">tailmessagetime = 900000  ; 15 minutes between tail messages</syntaxhighlight>
 +
 
 +
==tailsquashedtime===
 +
If a tail message is "squashed" by a user keying up over the top of it, a separate time value can be loaded to make the tail message be retried at a shorter time interval than the standard tailmessagetime= setting. The tailsquashedtime= setting takes a value in milliseconds.
 +
 
 +
<syntaxhighlight lang="ini">tailsquashedtime = 300000  ; 5 minutes</syntaxhighlight>
 +
 
 +
==totime===
 +
This defines the time out timer interval. The value is in milliseconds. The default value is 180000.
 +
 
 +
<syntaxhighlight lang="ini">totime = 180000  ; Repeater timeout 3 minutes </syntaxhighlight>
 +
 
 +
Related: [[#COP Commands | COP Commands 7 and 8]] and [[#controlstates= | controlstates=]] and [[#Control States Stanza | Control States Stanza]]
 +
 
 +
==unlinkedct===
 +
The unlinkedct setting selects the courtesy tone to be used when the system has no remote nodes connected and is operating as a standalone repeater.
 +
 
 +
<syntaxhighlight lang="ini>
 +
unlinkedct = ct2  ; use courtesy tone 2
 +
</syntaxhighlight>
 +
 
 +
==wait-times===
 +
Wait-times points to the [[#Wait Times Stanza|Wait Times Stanza]].
 +
 
 +
<syntaxhighlight lang="ini>
 +
wait-times = wait-times  ; name wait-times to 'wait-times'
 +
</syntaxhighlight>
 +
 
 +
=Functions Stanza=
 +
The functions stanza is a named stanza [[Structure of Config Files#Settings to name other Stanzas|pointed to]] by the [[#functions=|function=]] key/value pair.  Functions within this stanza are used to decode DTMF commands when accessing the node from its receiver.  This stanza is typically named 'functions'. 
 +
 
 +
<syntaxhighlight lang="ini>
 +
functions = functions  ; name the functions stanza 'functions'
 +
 
 +
[functions]
 +
...
 +
</syntaxhighlight>
 +
See [[#DTMF Commands|DTMF Commands]] for the list of functions available.
 +
 
 +
=Link Functions Stanza=
 +
The link functions stanza is a named stanza [[Structure of Config Files#Settings to name other Stanzas|pointed to]] by the [[#link_functions=|link_function=]] key/value pair.  Functions within this stanza are used decode DTMF commands when accessing the node via a link from another node. The traditional usage is to point link_functions= to the same stanza as named  by [[#functions=|functions=]] thereby having functions from a linked node and from the local node the same.
 +
 
 +
<syntaxhighlight lang="ini>
 +
functions = functions        ; name the functions stanza 'functions'
 +
link_functions = functions  ; use the same stanza
 +
 
 +
[functions]
 +
...
 +
</syntaxhighlight>
 +
If a different set of either limited or more capable functions is desired:
 +
<syntaxhighlight lang="ini>
 +
functions = functions                ; name the functions stanza 'functions'
 +
link_functions = my_link_functions  ; use a different stanza
 +
 
 +
[functions]
 +
...
 +
 
 +
[my_link_functions]
 +
...
 +
</syntaxhighlight>
 +
See [[#DTMF Commands|DTMF Commands]] for the list of functions available.
 +
 
 +
=Phone Functions Stanza=
 +
The phone functions stanza is a named stanza [[Structure of Config Files#Settings to name other Stanzas|pointed to]] by the [[#phone_functions=|phone_function=]] key/value pair.  Functions within this stanza are used decode DTMF commands when accessing the node from a telephone. The traditional usage is to point phone_functions= to the same stanza as named  by [[#functions=|functions=]] thereby having functions from a phone and from the local node the same.
 +
 
 +
<syntaxhighlight lang="ini>
 +
functions = functions        ; name the functions stanza 'functions'
 +
phone_functions = functions  ; use the same stanza
 +
 
 +
[functions]
 +
...
 +
</syntaxhighlight>
 +
If a different set of either limited or more capable functions is desired:
 +
<syntaxhighlight lang="ini>
 +
functions = functions                  ; name the functions stanza 'functions'
 +
phone_functions = my_phone_functions  ; use a different stanza
 +
 
 +
[functions]
 +
...
 +
 
 +
[my_phone_functions]
 +
...
 +
</syntaxhighlight>
 +
See [[#DTMF Commands|DTMF Commands]] for the list of functions available.
 +
 
 +
=Macro Stanza=
 +
The marco stanza is named stanza pointed to by the [[#macro=|macro=]] key/value pair. Macros are DTMF shortcuts.
 +
 
 +
<syntaxhighlight lang="ini>
 +
macro=macro  ; use stanza names 'macros'
 +
 
 +
[macro]
 +
1 = *32000*32001    ; connect to nodes 2000 and 2001
 +
</syntaxhighlight>
 +
 
 +
[https://wiki.allstarlink.org/index.php?title=Macro_use_and_format&modqueued=1 Full Macro Use And Format]
 +
 
 +
=Remote Base Stanza=
 +
Here are [[Structure of Config Files|key/value pairs]] required to configure a remote base.
 +
 
 +
==authlevel===
 +
The authlevel= key is used to enable or disable login requirements for a remote base.
 +
 
 +
* authlevel=0 Disables all access control (not recommended, unsecured)
 +
* authlevel=1 Enables access control, and waits for key up before prompting for the access code
 +
* authlevel=2 Enables access control, and prompts for the access code at the time of connection
 +
 
 +
<syntaxhighlight lang="ini>
 +
autllevel = 0  ; allow all comers
 +
</syntaxhighlight>
 +
 
 +
==civaddr===
 +
civaddr= is used with ICOM band radios to set the CIV address. The value is a 2 digit hexadecimal number. If this key is not specified, then the CIV address will be set to the default of 88.
 +
 
 +
<syntaxhighlight lang="ini>
 +
civaddr = 98  ; set CIV to 98
 +
</syntaxhighlight>
 +
 
 +
==Remote Base functions===
 +
functions= is a pointer to a remote base function stanza.
 +
 
 +
<syntaxhighlight lang="ini>
 +
functions = functions-remote  ; name the functions stanza 'functions-remote'
 +
 
 +
[functions-remote]
 +
...
 +
</syntaxhighlight>
 +
 
 +
See [[#Remote Base Functions Stanza|Remote Base Functions Stanza]].
 +
 
 +
==ioaddr===
 +
ioaddr= refers to a parallel port I/O address. It is specified as a hexadecimal number with a 0x prefix. The parallel port is used when the Doug Hall RBI-1 interface is employed.
 +
 
 +
<syntaxhighlight lang="ini>
 +
ioaddr = 0x378  ; set RB-1 address
 +
</syntaxhighlight>
 +
 
 +
==ioport===
 +
ioport= sets the serial port. On Linux Systems, these are typically path names to special files in the /dev directory.
 +
 
 +
<syntaxhighlight lang="ini>
 +
ioport = /dev/ttyS1  ; Linux com1
 +
</syntaxhighlight>
 +
 
 +
==Remote Base phone_functions===
 +
phone_functions= is a pointer to a remote base phone function stanza. It is equivalent to phone_functions in the [[#Phone Functions Stanza|Phone Functions Stanza]] but provides a separate set of commands. 
 +
 
 +
<syntaxhighlight lang="ini>
 +
phone_functions = functions-remote
 +
</syntaxhighlight>
 +
 
 +
==remote===
 +
remote= sets the type of radio. It also ensures that the node will be defined as a remote base node and not a standard node.
 +
 
 +
<syntaxhighlight lang="ini>
 +
remote = xcat  ; set xcat interface
 +
</syntaxhighlight>
 +
 
 +
{| class="wikitable"
 +
! Radio !! Value !! Comments
 +
|-
 +
| Dumb || y || Use for single channel remote base radios
 +
|-
 +
| FT-897 || ft897 || Must specify serial port using ioport=
 +
|-
 +
| TMG-707 || kenwood || Must specify serial port using ioport=
 +
|-
 +
| IC-706 || ic706 || Must specify serial port using ioport=. Must specify civaddr using civaddr=
 +
|-
 +
| TM-271 || tm271 || Must specify serial port using ioport=
 +
|-
 +
| Syntor Xcat || xcat || Must specify serial port using ioport=. Must specify civaddr using civaddr=
 +
|-
 +
| Doug Hall || rbi || Requires Parallel Port Address https://wiki.allstarlink.org/wiki/Remote_Base:_Doug_Hall_RBI-1=
 +
|}
 +
 
 +
==remote_inact_timeout===
 +
 
 +
Specifies the amount of time without keying from the link. Set to 0 to disable timeout.
 +
 
 +
<syntaxhighlight lang="ini>
 +
remote_inact_timeout = 0  ; do not time out
 +
</syntaxhighlight>
 +
 
 +
==remote_timeout===
 +
Session time out for remote base. Set to 0 to disable.
 +
 
 +
<syntaxhighlight lang="ini>
 +
remote_timeout = 0  ; do not timeout
 +
</syntaxhighlight>
 +
 
 +
==remote_timeout_warning===
 +
 
 +
==remote_timeout_freq===
 +
 
 +
==Remote Base rxchannel===
 +
This should contain the name of a usb radio interface which has been defined in [[usbradio.conf]] or a zaptel interface number if using a Quad Radio PCI Card.
 +
 
 +
<syntaxhighlight lang="ini>
 +
rxchannel = usbRadio/usb1
 +
</syntaxhighlight>
 +
 
 +
==Sample Remote Configuration==
 +
<syntaxhighlight lang="ini>
 +
[1234]
 +
; Rx audio/signaling channel                                                                                 
 +
rxchannel = Radio/usb
 +
 
 +
; Serial port for control
 +
ioport = /dev/ttyS1
 +
 
 +
; Radio Type               
 +
remote = ft897
 +
 
 +
; Function list from link                                         
 +
functions = functions-remote 
 +
 
 +
; Function list from phone       
 +
phone_functions = functions-remote
 +
 
 +
; Authorization level                                       
 +
authlevel = 0     
 +
</syntaxhighlight>
  
 
=Nodes Stanza=
 
=Nodes Stanza=
 +
The [nodes] stanza is a list of nodes, their IP addresses, port and "NONE" for non-remote base nodes. The nodes stanza is used to identify which node is mapped to which Internet call and to determine the destination to send the call to. If you are using automatic update for Allstar link (public) nodes, no Allstar link nodes should be defined here. Only place a definition for your local nodes, and private (off of allstar link) nodes or nodes behind the same NAT router here.
 +
 +
<syntaxhighlight lang="ini>
 
[nodes]
 
[nodes]
 +
1000 = radio@127.0.0.1/1000,NONE              ; Private hub on this server
 +
1001 = radio@host.domain.com/1001,NONE        ; Private node on another server
 +
2501 = radio@127.0.0.1/2501,NONE              ; Public node on this server
 +
2502 = radio@127.0.0.1/2502,NONE              ; Another public node on this server
 +
2503 = radio@192.168.1.20:4570/2503,NONE      ; Public node behind the same NAT router
 +
</syntaxhighlight>
 +
The [nodes] stanza performs a function similar to an OS hosts file. When looking up node information, app_rpt looks in the [nodes] stanza first then searches (what could be called the Allstar DNS) the /var/lib/asterisk/rpt_extnodes file.
 +
 
=Telemetry Stanza=
 
=Telemetry Stanza=
 +
This stanza is named by the telemetry= key/value pair. Telemetry entries can be shared across all nodes on the Asterisk/app_rpt server, or defined for each node. Can be a tone sequence, morse string, or a file as follows:
 +
 +
* |t - Tone escape sequence:
 +
** Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude). Single frequencies are created by setting freq1 or freq2 to zero.
 +
* |m - Morse escape sequence:
 +
**Sends Morse code at the '''telemetry amplitude and telemetry frequency''' as defined in the [morse] section. Follow with an alphanumeric string.
 +
* |i - Morse ID escape sequence:
 +
**Sends Morse code at the '''ID amplitude and ID frequency''' as defined in the [morse] section. Follow with an alphanumeric string.
 +
* Path to sound file:
 +
**Specify the path to a sound file on the server. Do not include file extension.
 +
 +
<syntaxhighlight lang="ini>
 +
[telemetry]
 +
ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
 +
ct2=|t(660,880,150,2048) 
 +
ct3=|t(440,0,150,4096)
 +
ct4=|t(550,0,150,2048)
 +
ct4=|t(2475,0,250,768)
 +
ct5=|t(660,0,150,2048)
 +
ct6=|t(880,0,150,2048)
 +
ct7=|t(660,440,150,2048)
 +
ct8=|t(700,1100,150,2048)
 +
ct9=|t(1633,0,50,1000)(0,0,30,0)(1209,0,50,1000);
 +
;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
 +
remotetx=|t(880,0,150,2048)
 +
remotemon=|t(1209,0,50,2048)
 +
cmdmode=|t(900,903,200,2048)
 +
functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
 +
patchup=rpt/callproceeding
 +
patchdown=rpt/callterminated
 +
 +
What the numbers mean,
 +
(000,000,010,000)
 +
  |  |  |  |-------amplitude
 +
  |  |  |-------------duration
 +
  |  |-------------------Tone 2
 +
  |-------------------------Tone 1
 +
 +
</syntaxhighlight>
  
 
=Morse Stanza=
 
=Morse Stanza=
 +
Morse code parameters, these are common to all nodes on a given Asterisk/app_rpt server.
 +
 +
<syntaxhighlight lang="ini>
 +
[morse]
 +
speed = 20            ; Approximate speed in WPM
 +
frequency = 900      ; Morse Telemetry Frequency
 +
amplitude = 4096      ; Morse Telemetry Amplitude
 +
idfrequency = 746    ; Morse ID Frequency 
 +
idamplitude = 768    ; Morse ID Amplitude
 +
</syntaxhighlight>
  
 
=Wait Times Stanza=
 
=Wait Times Stanza=
 +
This stanza is named by the [[#wait-times=|wait-times=]] key/value pair. The wait time stanza is used to set delay time between various node actions and their response. Values are in milliseconds.
 +
 +
<syntaxhighlight lang="ini>
 +
wait-times = wait-times  ; name the stanza 'wait-times'
  
=Memory Stanza=
+
[wait-times]                                                                                               
 +
telemwait = 2000
 +
idwait = 500
 +
unkeywait = 2000
 +
calltermwait = 2000
 +
</syntaxhighlight>
  
=Macro Stanza=
+
=Remote Base Memory Stanza=
 +
Remote base memories are in the format of:
 +
 
 +
memory = rxfreq,plfreq,txpower,offset,tone
 +
 
 +
<syntaxhighlight lang="ini>
 +
[memory]
 +
00 = 146.580,100.0,m
 +
01 = 147.030,103.5,m+t
 +
02 = 147.240,103.5,m+t
 +
03 = 147.765,79.7,m-t
 +
04 = 146.460,100.0,m
 +
05 = 146.550,100.0,m
 +
</syntaxhighlight>
  
 
=Control States Stanza=
 
=Control States Stanza=
  
There are several predefined nmemonics (keywords) used in the control state stanza to enable and disable the various features of the controller. These nmemonics correspond to the control operator command to be executed and most of these are the same groups of letters sent back when a single control operator command is executed on the controller.
+
There are several predefined nmemonics (keywords) used in the [controlstates] stanza to enable and disable the various features of the controller. These nmemonics correspond to the control operator command to be executed and most of these are the same groups of letters sent back when a single control operator command is executed on the controller.
  
 
{| class="wikitable"
 
{| class="wikitable"
Line 335: Line 1,054:
  
 
=Schedule Stanza=
 
=Schedule Stanza=
 +
The scheduler can execute commands at certain times. For example for a net on Tuesday nights at 8 PM.
 +
 +
<syntaxhighlight lang="ini>
 +
scheduler=schedule  ; name the stanza 'schedule'
 +
 +
[schedule]                                                                     
 +
;dtmf_function =  m h dom mon dow  ; ala cron, star is implied                                                 
 +
2 = 00 00 * * *  ; at midnight every day, execute macro 2.
 +
</syntaxhighlight>
  
 
=DAQ List Stanza=
 
=DAQ List Stanza=
Line 340: Line 1,068:
 
=Meter Faces Stanza=
 
=Meter Faces Stanza=
  
=Alarms Stanza=
+
=Alarms Stanza
 
 
[[Category:Node Configuration]]
 

Latest revision as of 18:47, 27 January 2022

Rpt.conf is where the majority of user-facing features, such as the node's CW and voice ID, DTMF commands and timers are set. There is a lot of capability here which can be difficult to grasp. Fortunately the default Node rpt.conf is well commented and will work fine for most node admins.

DTMF Commands

DTMF commands are placed in any one of three named stanzas. Function stanzas control access to DTMF commands that a user can issue from various control points.

A function stanza key/value pair has the following format:

dtmfcommand=functionclass,[functionmethod],[parameters] Where:

  • dtmfcommand is a DTMF digit sequence minus the start character (usually *)
  • functionclass is a string which defines what class of command; link, status or COP
  • functionmethod defines the optional method number to use in the function class.
  • functionoptions are one or more optional comma separated parameters which further define a command.

Status Commands

Status commands (functioncalss 'status') provide general information about the node.

712 = status,12   ; Give Time of Day (local only)
Status Description
1 Force ID (global)
2 Give Time of Day (global)
3 Give software Version (global)
4 Give GPS location info
5 Speak the last (dtmf) user
11 Force ID (local only)
12 Give Time of Day (local only)

Link Commands

Link commands (functioncalss 'link') connect to, disconnect from, monitor (Rx only) other nodes and give link status.

3 = ilink,3   ; Connect specified link -- transceive
ilink Description
1 Disconnect specified link
2 Connect specified link -- monitor only
3 Connect specified link -- tranceive
4 Enter command mode on specified link
5 System status
6 Disconnect all links
7 Last Node to Key Up
8 Connect specified link -- local monitor only
9 Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.
10 Disconnect all RANGER links (except permalinks)
11 Disconnect a previously permanently connected link
12 Permanently connect specified link -- monitor only
13 Permanently connect specified link -- tranceive
15 Full system status (all nodes)
16 Reconnect links disconnected with "disconnect all links"
17 MDC test (for diag purposes)
18 Permanently Connect specified link -- local monitor only

COP Commands

Control operator (functionclass 'cop') commands are privileged commands. Node admins may provide some of these to their user community based on personal preference.

99 = cop,7   ; enable timeout timer

Some COP commands can take multiple parameters. For example this COP 48 would send #3#607 on command.

900 = cop,48,#,3,#,6,0,7
COP Description
1 System warm boot
2 System enable
3 System disable
4 Test Tone On/Off
5 Dump System Variables on Console (debug)
6 PTT (phone mode only)
7 Time out timer enable
8 Time out timer disable
9 Autopatch enable
10 Autopatch disable
11 Link enable
12 Link disable
13 Query System State
14 Change System State
15 Scheduler Enable
16 Scheduler Disable
17 User functions (time, id, etc) enable
18 User functions (time, id, etc) disable
19 Select alternate hang timer
20 Select standard hang timer
21 Enable Parrot Mode
22 Disable Parrot Mode
23 Birdbath (Current Parrot Cleanup/Flush)
24 Flush all telemetry
25 Query last node un-keyed
26 Query all nodes keyed/unkeyed
27 Reset DAQ minimum on a pin
28 Reset DAQ maximum on a pin
30 Recall Memory Setting in Attached Xcvr
31 Channel Selector for Parallel Programmed Xcvr
32 Touchtone pad test: command + Digit string + # to playback all digits pressed
33 Local Telemetry Output Enable
34 Local Telemetry Output Disable
35 Local Telemetry Output on Demand
36 Foreign Link Local Output Path Enable
37 Foreign Link Local Output Path Disable
38 Foreign Link Local Output Path Follows Local Telemetry
39 Foreign Link Local Output Path on Demand
42 Echolink announce node # only
43 Echolink announce node Callsign only
44 Echolink announce node # & Callsign
45 Link Activity timer enable
46 Link Activity timer disable
47 Reset "Link Config Changed" Flag
48 Send Page Tone (Tone specs separated by parenthesis)
49 Disable incoming connections (control state noice)
50 Enable incoming connections (control state noicd)
51 Enable sleep mode
52 Disable sleep mode
53 Wake up from sleep
54 Go to sleep
55 Parrot Once if parrot mode is disabled
56 Rx CTCSS Enable
57 Rx CTCSS Disable
58 Tx CTCSS On Input only Enable
59 Tx CTCSS On Input only Disable
60 Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])

Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. DestID and subcode are only specified for the 'C' type message. UnitID is the local systems UnitID. DestID is the MDC1200 ID of the radio being called, and the subcodes are as follows: Subcode '8205' is Voice Selective Call for Spectra ('Call') Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or Astro-Saber('Call') Subcode '810D' is Call Alert (like Maxtrac 'CA')

61 Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
62 Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
63 Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])
64 Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])
65 Send POCSAG page (equipped channel types only)

Remote Base Commands

Remote base commands (functionclass 'remote') provide remote base control. This stanza is named by the remote base Remote Base Functions key/value pair.

remote Description
1 Retrieve Memory
2 Set freq.
3 Set tx PL tone
4 Set rx PL tone
5 Long status query
99,CALLSIGN,LICENSETAG Remote Base login
100 Rx PL off
101 Rx PL on
102 Tx PL off
103 Tx PL on
104 Low Power
105 Medium Power
106 High Power
107 Bump -20
108 Bump -100
109 Bump -500
110 Bump +20
111 Bump +100
112 Bump +500
113 Scan - slow
114 Scan - quick
115 Scan - fast
116 Scan + slow
117 Scan + quick
118 Scan + fast
119 Tune
140 Short status query
210 Send a *
211 Send a #

Not all commands above are supported by all radios. For example radios which don't support SSB, would not be able to be placed in LSB or USB mode.

Remote Base Login

When authlevel= is greater than zero, remote 99 is used to define a different dtmf sequence for each user authorized to use the remote base. The remote base will announce the callsign as access is granted.

[remote node#]
authlevel = 2 ; Remote base authentication level
; authlevel = 0 : Anyone can use it
; authlevel = 1 : Requires log in, Waits for Tx key to ask for it
; authlevel = 2 : Requires log in, asks for it automously

[remote-functions]
8xx=remote,99,OK,E ; password
9139583 = remote,99,WB6NIL,G   ; grant access to Jim (general)
9148351 = remote,99,WA6ZFT,E   ; grant access to Steve (extra)

When the remote base is disconnected from the originating node, the user will be logged out.

The LICENSETAG argument is used to enforce tx frequency limits. Need info [txlimits].

Settings to name other Stanzas

Within the node stanza, some key=value pairs point to other stanzas. This allows nodes on the same Asterisk/app_rpt server to have the same settings (without duplicate entries) or different settings in some cases. For example the phone patch command may be *6 on one node, yet *61 on another.

For example:

[1000]
functions=functionsVHF

[1001]
functions=functionsVHF

[1002]
functions=functionsUHF

[functionsVHF]
; Two meter Autopatch up is *6
6=autopatchup,noct=1,farenddisconnect=1,dialtime=20000 
0=autopatchdn       ; Autopatch down

[functionsUHF]
; 440 Autopatch up is *61
61=autopatchup,noct=1,farenddisconnect=1,dialtime=20000  ; Autopatch up
0=autopatchdn       ; Autopatch down
* controlstates=
* functions=
* link_functions=
* macro=
* phone_functions=
* telemetry=
* wait_times=

Node Number Stanza

The node number stanza is the first stanza in rpt.conf.

[1999]    ; Replace with your assigned node number

The node number stanza contains the following key/value pairs.

althangtime=

This controls the length of the repeater hang time when the alternate hang timer is selected with a control operator function. It is specified in milliseconds.

althangtime=4000   ; 4 seconds

beaconing=

When set to 1 will send the repeater ID at the idtime interval regardless of whether there was repeater activity or not. This feature appears to be required in the UK, but is probably illegal in the US.

beaconing=1   ;Set to 1 to beacon. Defaults to 0

callerid=

This setting allows the autopatch on the node to be identified with a specific caller ID. The default setting is as follows

callerid="Repeater" <0000000000>

Note: The value in quotes is the name of the autopatch caller, and the numbers in angle brackets are the originating telephone number to use.

connpgm= and discpgm=

Runs user defined scripts. Example from https://www.qsl.net/k0kn/swissarmy_debian

# Place these lines in rpt.conf for each node:
#     connpgm=/home/kyle/swissarmy 1
#     discpgm=/home/kyle/swissarmy 0

context=

This setting directs the autopatch for the node to use a specific context in extensions.conf for outgoing autopatch calls. The default is to specify a context name of radio.

context=radio

controlstates=

This setting defines the name of the variable named control state stanza. Control states are an optional feature which allows groups of control operator commands to be executed all at once. To use control states, define an entry in your node stanzas to point to a dedicated control state stanza like this:

controlstates = controlstates   ; points to control state stanza
[controlstates]
0 = rptena,lnkena,apena,totena,ufena,noicd  ; Normal operation                                  
1 = rptena,lnkena,apdis,totdis,ufena,noice  ; Net and news operation                                             
2 = rptena,lnkdis,apdis,totena,ufdis,noice  ; Repeater only operation

The control state stanza describes these mnemonics.

duplex=

The duplex key/value pairs sets the duplex mode for desired radio operation. Duplex mode 2 is the default if none specified.

Duplex Mode Description
0 Half duplex with no telemetry tones or hang time. Special Case: Full duplex if linktolink is set to yes. This mode is preferred when interfacing with an external multiport repeater controller. Comment out idrecording and idtalkover to suppress IDs.
1 Half duplex with telemetry tones and hang time. Does not repeat audio. This mode is preferred when interfacing a simplex node.
2 Full Duplex with telemetry tones and hang time. This mode is preferred when interfacing a repeater.
3 Full Duplex with telemetry tones and hang time, but no repeated audio. See details
4 Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.
duplex = 0     ; 0 = Half duplex with no telemetry tones or hang time.

endchar=

This setting allows the end character used by some control functions to be changed. By default this is a #. The endchar value must not be the same as the funcchar default or overridden value.

erxgain=

Echolink receive gain adjustment in +/- db-volts. Used to balance Echolink recieve audio on an app_rpt node.

erxgain = -3

See Echolink How to

etxgain=

Echolink transmit gain adjustment in +/- db-volts. Used to balance Echolink transmit audio on an app_rpt node.

etxgain = 3

See Echolink How to

funcchar=

This setting can be used to change the default function starting character of * to something else. Please note that the new value chosen must not be the same as the default or overridden value for endchar=.

functions=

This names (points to) the function stanza.

functions = functionsUHF   ; pointer to 440 repeater functions stanza

GUI

Key Valid Values Default
guilinkdefault 0 = telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode 1
guilinkdynamic 0 = disallow users to change the gui telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command 1

Function Classes

Function classes are names for categories of functions. There are several function classes defined. They are described in the table below:

Class Description
cop Control operator commands
ilink Internet linking commands
status User Status Commands
autopatchup Autopatch up commands
autopatchdn Autopatch down commands
remote Remote base commands
macro Command Macros

Most of the above command classes require a function method and possibly one or more additional command parameters. Function methods are discussed next.

Function Methods

Function methods are numbers which identify a specific function to execute within a function class. Function Methods are optional and in some cases should be omitted (Such as with the autopatchup method) A complete and up-to-date description of all functon methods can be found in the app_rpt.c source file. Some function methods are shown below as an example below:

1  - Force ID (global)
2  - Give Time of Day (global)
3  - Give software Version (global)
11 - Force ID (local only)
12 - Give Time of Day (local only)

Function Options

Some Function Methods can take function options. These are specified after the Function Method separated with commas. Not all commands require or take Function options. An example of a method which can accept Function Options is the autopatchup method.

Putting it all Together

A small excerpt from the function stanza of rpt.conf is hown below.

[functions]
1=ilink,1                                               ; Specific link disconnect
6=autopatchup,noct=1,farenddisconnect=1,dialtime=2000   ; Autopatch up

The above example contains DTMF functions with all of the parameters discussed on previous pages.

In the above example:

  • *1 followed by a node number disconnects a specific link. The function class is ilink and the function method is 1
  • *6 followed by a phone number brings up the autopatch with the function options specified. Note that there is no function method defined, but there are function options present.

hangtime=

This controls the length of the repeater hang time. It is specified in milliseconds.

hangtime = 1000   ;Set hang time for 1 second

holdofftelem=

This node stanza configuration key forces all telemetry to be held off until a local user on the receiver or a remote user over a link unkeys. There is one exception to this behavior: When an ID needs to be sent and there is activity coming from a linked node.

holdofftelem = 1   ;Set to 1 to hold off. Default is 0

telemdefault=

telemdefault =  0 = telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter. Default is 1

telemdynamic=

telemdynamic = 0 = disallow users to change the local telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command. Default is 1

phonelinkdefault=

phonelinkdefault = 0 = telemetry output off, 1 = telemetry output on, 2 = timed telemetry output on command execution and for a short time thereafter, 3 = follow local telemetry mode  Default is 1

phonelinkdynamic=

phonelinkdynamic = 0 = disallow users to change phone telemetry setting with a COP command, 1 = Allow users to change the setting with a COP command  Default is 1

idrecording=

The identifier message is stored in the node stanza using the idrecording key. It can be changed to a different call sign by changing the value to something different. The value can be either a morse code identification string prefixed with |i, or the name of a sound file containing a voice identification message. When using a sound file, the default path for the sound file is /var/lib/asterisk/sounds.

idrecording = |iwa6zft/r   ; Morse Code ID

or

idrecording = /var/lib/asterisk/sounds/myid   ; Voice ID

Note: ID recording files must have extension gsm,ulaw,pcm, or wav. The extension is left off when it is defined as the example shows above. File extensions are used by Asterisk to determine how to decode the file. All ID recording files should be sampled at 8KHz. See Recording audio files

idtalkover=

The ID talkover message is stored in the node stanza using the idtalkover setting. The purpose of idtalkover is to specify an alternate ID to use when the ID must be sent over the top of a user transmission, This can be a shorter voice ID or an ID in morse code. The value can be either a morse code identification string prefixed with |i, or the name of a sound file containing a voice identification message. When using a sound file, the default path for the sound file is /var/lib/asterisk/sounds. Example usages are as follows:

idtalkover = |iwa6zft/r   ; Morse Code ID

or

idtalkover = /var/lib/asterisk/sounds/myid   ; Voice ID

Note: ID recording files must have extension gsm,ulaw,pcm, or wav. The extension is left off when it is defined as the example shows above. File extensions are used by Asterisk to determine how to decode the file. All ID recording files should be sampled at 8KHz. See Recording audio files

inxlat=

The inxlat setting allows complete remapping of the funcchar and endchar digits to different digits or digit sequences. inxlat acts on the digits received by the radio receiver on the node.

Format: inxlat = funchars,endchars,passchars,dialtone

where:

  • funcchars is the digit or digit sequence to replace funcchar
  • endchars is the digit or digit sequence to replace endchar
  • passchars are the digits to pass through (can be used to block certain digits)
  • dialtone is optional. Set to Y for dial tone on successful funcchars.
inxlat = #56,#57,0123456789ABCD ; string xlat from radio port to sys

link_functions=

This names (points to) the link_functions stanza.

The link_functions setting directs the node to use a particular function stanza for functions dialed by users accessing the node via a link from another node. The traditional default is to point it to a function stanza named "functions".

link_functions = functions ; pointer to the Link Function stanza

linkmongain=

Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. If linkmongain set to a positive number monitored audio will increase by the set amount in db. The value of linkmongain is in db. The default value is 0 db.

linkmongain = -20   ; reduce link volume 20dB

linktolink=

When operating in duplex mode 0, this forces the radio interface to operate in full duplex mode, but keeps all the other duplex mode 0 semantics. This is used when a radio interface is connected to a multiport analog repeater controller. The linktolink= key can take two values: yes or no.

linktolink = yes   ; set to yes to enable. Default is no.

linkunkeyct=

The linkunkeyct setting selects the courtesy tone to send when a connected remote node unkeys. The default is no courtesy tone when a remote node unkeys.

linkunkeyct = ct8  ; use courtesy tone 8

macro=

The marco key/value points to by the Macro Stanza key/value pair. Macros are DTMF shortcuts.

macro=macro   ; use stanza names 'macros'

[macro]
1 = *32000*32001     ; connect to nodes 2000 and 2001

nounkeyct=

The nounkeyct node stanza key completely disables the courtesy tone. This is useful for eliminating TX time in applications using simplex uplinks to repeaters on the repeater pair itself. This practice is strongly discouraged.

nounkeyct = yes  ; :(

politeid=

The politeid setting specified the number of milliseconds prior to the end of the id cycle where the controller will attempt to play the ID in the tail when a user unkeys. If the controller does not get a chance to send the ID in the tail, the ID will be played over the top of the user transmission. Optional, default 30000.

politeid = 30000   ; 30 seconds

propagate_dtmf=

Takes either yes or no. When set to yes, DTMF will be regenerated from out-of-band signalling or from from the receiver dtmf decoder whenever a function start character is NOT detected and command decoding has not begun. When set to no, no tones will be regenerated. The default for this setting is no. This setting is meant to be used in conjunction with linktolink, inxlat, and outxlat when interfacing a radio port to a multiport analog repeater controller on an RF-linked system.

propagate_dtmf = no

Note: There is a separate setting propagate_phonedtmf for use by dial-in (phone and dphone) users.

remotect=

The remotect setting allows the selection of the remote linked courtesy tone so that the users can tell there is a remote base connected locally.

remotect = ct3   ; use courtesy tone 3

rxburstfreq=

If rx tone burst operation is desired, specify the frequency in hertz of the desired tone burst. Setting to 0 (or not specifying) indicates no tone burst operation.

rxburstfreq = 1000

rxburstthreshold=

In rx toneburst mode, specifies the minimum signal to noise ratio in db that qualifies a valid tone. Defaults to 16 (db).

rxbursttime=

For rx toneburst operation, specifies minimum amount of time that tone needs to be valid for recognition (in milliseconds). Defaults to 250.

rxchannel=

The rxchannel key/value pair selects the radio interface. There must be one (and only one) rxchannel per node. The selections are:

Value Description
dahdi/pseudo No radio, used for hubs
SimpleUSB/usb_1999 SimpleUSB (limited DSP)
Radio/usb_1999 USBRadio (full DSP)
voter/1990 RTCM
Pi/1 Raspberry Pi PiTA
Dahdi/1 PCI Quad card
Beagle/1 BeagleBoard
USRP/127.0.0.1:34001:32001 GNU Radio interface USRP
rxchannel = dahdi/pseudo     ; No radio (hub)

Note: This is selecting what is known as (in Asterisk terminology) the channel driver.

scheduler=

This setting defines the scheduler stanza. The scheduler is used to execute commands at a particular time.

scheduler = schedule   ; name scheduler to 'schedule'

[schedule]
...

sleeptime=

This sets the inactivity period in seconds for no signal on the repeater receiver before the system goes to sleep.

sleeptime = 300   ; go to sleep after 5 mins of no activity

startup_macro=

The startup_macro is executed once on system startup. Each node can have one startup macro defined in its node stanza.

startup_macro = *31000 *31001 *31002   ; Connect to 1000, 1001 and 1002 at startup

One string of one or multiple commands executed in order. Note that this line of commands does NOT terminate with a # like a normal macro. And you can call any number of regular macros with it.

tailmessagelist=

The tailmessagelist setting allows a comma separated list of audio files to be specified for the tail message function. The tail messages will rotate from one to the next until the end of the list is reached at which point the first message in the list will be selected. If no absolute path name is specified, the directory var/lib/asterisk/sounds will be searched for the sound file. The file extension should be omitted.

tailmessagelist = welcome,clubmeeting,wx   ; rotate 3 tail messages

Note: ID recording files must have extension gsm,ulaw,pcm, or wav. The extension is left off when it is defined as the example shows above. File extensions are used by Asterisk to determine how to decode the file. All ID recording files should be sampled at 8KHz. See Recording audio files

tailmessagetime=

This sets the amount of time in milliseconds between tail messages. Tail Messages are played when a user unkeys on the repeater input at the point where the hang timer expires after the courtesy tone is sent.

tailmessagetime = 900000   ; 15 minutes between tail messages

tailsquashedtime=

If a tail message is "squashed" by a user keying up over the top of it, a separate time value can be loaded to make the tail message be retried at a shorter time interval than the standard tailmessagetime= setting. The tailsquashedtime= setting takes a value in milliseconds.

tailsquashedtime = 300000   ; 5 minutes

totime=

This defines the time out timer interval. The value is in milliseconds. The default value is 180000.

totime = 180000   ; Repeater timeout 3 minutes

Related: COP Commands 7 and 8 and controlstates= and Control States Stanza

unlinkedct=

The unlinkedct setting selects the courtesy tone to be used when the system has no remote nodes connected and is operating as a standalone repeater.

unlinkedct = ct2   ; use courtesy tone 2

wait-times=

Wait-times points to the Wait Times Stanza.

wait-times = wait-times   ; name wait-times to 'wait-times'

Functions Stanza

The functions stanza is a named stanza pointed to by the function= key/value pair. Functions within this stanza are used to decode DTMF commands when accessing the node from its receiver. This stanza is typically named 'functions'.

functions = functions   ; name the functions stanza 'functions'

[functions]
...

See DTMF Commands for the list of functions available.

Link Functions Stanza

The link functions stanza is a named stanza pointed to by the link_function= key/value pair. Functions within this stanza are used decode DTMF commands when accessing the node via a link from another node. The traditional usage is to point link_functions= to the same stanza as named by functions= thereby having functions from a linked node and from the local node the same.

functions = functions        ; name the functions stanza 'functions'
link_functions = functions   ; use the same stanza 

[functions]
...

If a different set of either limited or more capable functions is desired:

functions = functions                ; name the functions stanza 'functions'
link_functions = my_link_functions   ; use a different stanza

[functions]
...

[my_link_functions]
...

See DTMF Commands for the list of functions available.

Phone Functions Stanza

The phone functions stanza is a named stanza pointed to by the phone_function= key/value pair. Functions within this stanza are used decode DTMF commands when accessing the node from a telephone. The traditional usage is to point phone_functions= to the same stanza as named by functions= thereby having functions from a phone and from the local node the same.

functions = functions         ; name the functions stanza 'functions'
phone_functions = functions   ; use the same stanza 

[functions]
...

If a different set of either limited or more capable functions is desired:

functions = functions                  ; name the functions stanza 'functions'
phone_functions = my_phone_functions   ; use a different stanza

[functions]
...

[my_phone_functions]
...

See DTMF Commands for the list of functions available.

Macro Stanza

The marco stanza is named stanza pointed to by the macro= key/value pair. Macros are DTMF shortcuts.

macro=macro   ; use stanza names 'macros'

[macro]
1 = *32000*32001     ; connect to nodes 2000 and 2001

Full Macro Use And Format

Remote Base Stanza

Here are key/value pairs required to configure a remote base.

authlevel=

The authlevel= key is used to enable or disable login requirements for a remote base.

  • authlevel=0 Disables all access control (not recommended, unsecured)
  • authlevel=1 Enables access control, and waits for key up before prompting for the access code
  • authlevel=2 Enables access control, and prompts for the access code at the time of connection
autllevel = 0   ; allow all comers

civaddr=

civaddr= is used with ICOM band radios to set the CIV address. The value is a 2 digit hexadecimal number. If this key is not specified, then the CIV address will be set to the default of 88.

civaddr = 98  ; set CIV to 98

Remote Base functions=

functions= is a pointer to a remote base function stanza.

functions = functions-remote   ; name the functions stanza 'functions-remote'

[functions-remote]
...

See Remote Base Functions Stanza.

ioaddr=

ioaddr= refers to a parallel port I/O address. It is specified as a hexadecimal number with a 0x prefix. The parallel port is used when the Doug Hall RBI-1 interface is employed.

ioaddr = 0x378   ; set RB-1 address

ioport=

ioport= sets the serial port. On Linux Systems, these are typically path names to special files in the /dev directory.

ioport = /dev/ttyS1   ; Linux com1

Remote Base phone_functions=

phone_functions= is a pointer to a remote base phone function stanza. It is equivalent to phone_functions in the Phone Functions Stanza but provides a separate set of commands.

phone_functions = functions-remote

remote=

remote= sets the type of radio. It also ensures that the node will be defined as a remote base node and not a standard node.

remote = xcat   ; set xcat interface
Radio Value Comments
Dumb y Use for single channel remote base radios
FT-897 ft897 Must specify serial port using ioport=
TMG-707 kenwood Must specify serial port using ioport=
IC-706 ic706 Must specify serial port using ioport=. Must specify civaddr using civaddr=
TM-271 tm271 Must specify serial port using ioport=
Syntor Xcat xcat Must specify serial port using ioport=. Must specify civaddr using civaddr=
Doug Hall rbi Requires Parallel Port Address https://wiki.allstarlink.org/wiki/Remote_Base:_Doug_Hall_RBI-1=

remote_inact_timeout=

Specifies the amount of time without keying from the link. Set to 0 to disable timeout.

remote_inact_timeout = 0   ; do not time out

remote_timeout=

Session time out for remote base. Set to 0 to disable.

remote_timeout = 0   ; do not timeout

remote_timeout_warning=

remote_timeout_freq=

Remote Base rxchannel=

This should contain the name of a usb radio interface which has been defined in usbradio.conf or a zaptel interface number if using a Quad Radio PCI Card.

rxchannel = usbRadio/usb1

Sample Remote Configuration

[1234]
; Rx audio/signaling channel                                                                                   
rxchannel = Radio/usb

; Serial port for control
ioport = /dev/ttyS1

; Radio Type                
remote = ft897 

; Function list from link                                          
functions = functions-remote  

; Function list from phone         
phone_functions = functions-remote

; Authorization level                                         
authlevel = 0

Nodes Stanza

The [nodes] stanza is a list of nodes, their IP addresses, port and "NONE" for non-remote base nodes. The nodes stanza is used to identify which node is mapped to which Internet call and to determine the destination to send the call to. If you are using automatic update for Allstar link (public) nodes, no Allstar link nodes should be defined here. Only place a definition for your local nodes, and private (off of allstar link) nodes or nodes behind the same NAT router here.

[nodes]
1000 = radio@127.0.0.1/1000,NONE               ; Private hub on this server 
1001 = radio@host.domain.com/1001,NONE         ; Private node on another server
2501 = radio@127.0.0.1/2501,NONE               ; Public node on this server
2502 = radio@127.0.0.1/2502,NONE               ; Another public node on this server
2503 = radio@192.168.1.20:4570/2503,NONE       ; Public node behind the same NAT router

The [nodes] stanza performs a function similar to an OS hosts file. When looking up node information, app_rpt looks in the [nodes] stanza first then searches (what could be called the Allstar DNS) the /var/lib/asterisk/rpt_extnodes file.

Telemetry Stanza

This stanza is named by the telemetry= key/value pair. Telemetry entries can be shared across all nodes on the Asterisk/app_rpt server, or defined for each node. Can be a tone sequence, morse string, or a file as follows:

  • |t - Tone escape sequence:
    • Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude). Single frequencies are created by setting freq1 or freq2 to zero.
  • |m - Morse escape sequence:
    • Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the [morse] section. Follow with an alphanumeric string.
  • |i - Morse ID escape sequence:
    • Sends Morse code at the ID amplitude and ID frequency as defined in the [morse] section. Follow with an alphanumeric string.
  • Path to sound file:
    • Specify the path to a sound file on the server. Do not include file extension.
[telemetry]
ct1=|t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2=|t(660,880,150,2048)  
ct3=|t(440,0,150,4096) 
ct4=|t(550,0,150,2048)
ct4=|t(2475,0,250,768)
ct5=|t(660,0,150,2048)
ct6=|t(880,0,150,2048)
ct7=|t(660,440,150,2048)
ct8=|t(700,1100,150,2048)
ct9=|t(1633,0,50,1000)(0,0,30,0)(1209,0,50,1000); 
;remotetx=|t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000);
remotetx=|t(880,0,150,2048) 
remotemon=|t(1209,0,50,2048) 
cmdmode=|t(900,903,200,2048)
functcomplete=|t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
patchup=rpt/callproceeding
patchdown=rpt/callterminated

What the numbers mean,
 (000,000,010,000)
   |   |   |   |-------amplitude
   |   |   |-------------duration
   |   |-------------------Tone 2
   |-------------------------Tone 1

Morse Stanza

Morse code parameters, these are common to all nodes on a given Asterisk/app_rpt server.

[morse]
speed = 20            ; Approximate speed in WPM
frequency = 900       ; Morse Telemetry Frequency
amplitude = 4096      ; Morse Telemetry Amplitude
idfrequency = 746     ; Morse ID Frequency  
idamplitude = 768     ; Morse ID Amplitude

Wait Times Stanza

This stanza is named by the wait-times= key/value pair. The wait time stanza is used to set delay time between various node actions and their response. Values are in milliseconds.

wait-times = wait-times   ; name the stanza 'wait-times'

[wait-times]                                                                                                 
telemwait = 2000
idwait = 500
unkeywait = 2000
calltermwait = 2000

Remote Base Memory Stanza

Remote base memories are in the format of:

memory = rxfreq,plfreq,txpower,offset,tone

[memory]
00 = 146.580,100.0,m
01 = 147.030,103.5,m+t
02 = 147.240,103.5,m+t
03 = 147.765,79.7,m-t
04 = 146.460,100.0,m
05 = 146.550,100.0,m

Control States Stanza

There are several predefined nmemonics (keywords) used in the [controlstates] stanza to enable and disable the various features of the controller. These nmemonics correspond to the control operator command to be executed and most of these are the same groups of letters sent back when a single control operator command is executed on the controller.

Nmemonic Description COP Method
rptena Repeater Enable 2
rptdis Repeater Disable 3
totena Timeout Timer Enable 7
totdis Timeout Timer Disable 8
apena Autopatch Enable 9
apdis Autopatch Disable 10
lnkena Link Enable 11
lnkdis Link Disable 12
skena Scheduler Enable 15
skdis Scheduler Disable 16
ufena User Functions Enable 17
ufdis User Functions Disable 18
atena Alternate Hangtime Enable 19
atdis Alternate Hangtime Disable 20
noice No Incoming Connections Enable 49
noicd No Incoming Connections Disable 50
slpen Sleep Mode Enable 51
slpds Sleep Mode Disable 52

Schedule Stanza

The scheduler can execute commands at certain times. For example for a net on Tuesday nights at 8 PM.

scheduler=schedule   ; name the stanza 'schedule'

[schedule]                                                                      
;dtmf_function =  m h dom mon dow  ; ala cron, star is implied                                                  
2 = 00 00 * * *   ; at midnight every day, execute macro 2.

DAQ List Stanza

Meter Faces Stanza

=Alarms Stanza