Difference between revisions of "Rpt.conf"
Jump to navigation
Jump to search
| Line 1: | Line 1: | ||
| + | ==COP (control operator) Commands== | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
Revision as of 21:09, 10 October 2017
COP (control operator) Commands
| COP | COP Function |
|---|---|
| 1 | System warm boot |
| 2 | System enable |
| 3 | System disable |
| 4 | Test Tone On/Off |
| 5 | Dump System Variables on Console (debug) |
| 6 | PTT (phone mode only) |
| 7 | Time out timer enable |
| 8 | Time out timer disable |
| 9 | Autopatch enable |
| 10 | Autopatch disable |
| 11 | Link enable |
| 12 | Link disable |
| 13 | Query System State |
| 14 | Change System State |
| 15 | Scheduler Enable |
| 16 | Scheduler Disable |
| 17 | User functions (time, id, etc) enable |
| 18 | User functions (time, id, etc) disable |
| 19 | Select alternate hang timer |
| 20 | Select standard hang timer |
| 21 | Enable Parrot Mode |
| 22 | Disable Parrot Mode |
| 23 | Birdbath (Current Parrot Cleanup/Flush) |
| 24 | Flush all telemetry |
| 25 | Query last node un-keyed |
| 26 | Query all nodes keyed/unkeyed |
| 27 | Reset DAQ minimum on a pin |
| 28 | Reset DAQ maximum on a pin |
| 30 | Recall Memory Setting in Attached Xcvr |
| 31 | Channel Selector for Parallel Programmed Xcvr |
| 32 | Touchtone pad test: command + Digit string + # to playback all digits pressed |
| 33 | Local Telemetry Output Enable |
| 34 | Local Telemetry Output Disable |
| 35 | Local Telemetry Output on Demand |
| 36 | Foreign Link Local Output Path Enable |
| 37 | Foreign Link Local Output Path Disable |
| 38 | Foreign Link Local Output Path Follows Local Telemetry |
| 39 | Foreign Link Local Output Path on Demand |
| 42 | Echolink announce node # only |
| 43 | Echolink announce node Callsign only |
| 44 | Echolink announce node # & Callsign |
| 45 | Link Activity timer enable |
| 46 | Link Activity timer disable |
| 47 | Reset "Link Config Changed" Flag |
| 48 | Send Page Tone (Tone specs separated by parenthesis) |
| 49 | Disable incoming connections (control state noice) |
| 50 | Enable incoming connections (control state noicd) |
| 51 | Enable sleep mode |
| 52 | Disable sleep mode |
| 53 | Wake up from sleep |
| 54 | Go to sleep |
| 55 | Parrot Once if parrot mode is disabled |
| 56 | Rx CTCSS Enable |
| 57 | Rx CTCSS Disable |
| 58 | Tx CTCSS On Input only Enable |
| 59 | Tx CTCSS On Input only Disable |
| 60 | Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])
Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. DestID and subcode are only specified for the 'C' type message. UnitID is the local systems UnitID. DestID is the MDC1200 ID of the radio being called, and the subcodes are as follows: Subcode '8205' is Voice Selective Call for Spectra ('Call') Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or Astro-Saber('Call') Subcode '810D' is Call Alert (like Maxtrac 'CA') |
| 61 | Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....) |
| 62 | Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....) |
| 63 | Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR]) |
| 64 | Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR]) |
| 65 | Send POCSAG page (equipped channel types only) |