VPN

The following contains information on various VPN setups that you can use.

IPSEC

Information on how to setup IPSEC tunnels.

Mikrotik to Strongswan

Use the following configurations to connect a system running Stongswan to a Mikrotik device using IPSEC.

Strongswan config

/etc/ipsec.conf:

  conn <name>
            authby=secret
            auto=route
            keyexchange=ike
            left=<your local IP>
            right=<remote IP of Mikrotik system>
            leftikeport=500
            rightikeport=500
            type=transport
            ike=aes256-sha1-modp1024!
            esp=aes256-sha1!
            dpddelay=5
            dpdtimeout=20
            dpdaction=clear

/etc/ipsec.secrets:

   <your local IP> <remote IP of Mikrotik system> :  PSK "<Put your preshared key here>"

Mikrotik Config

 /ip ipsec policy
 add src-address=0.0.0.0/0 dst-address=<remote IP of strongswan system> proposal=ike2 ipsec-protocols=esp
 
 /ip ipsec proposal
 add name="ike2" auth-algorithms=sha256,sha1 enc-algorithms=aes-256-cbc,aes-128-cbc lifetime=30m pfs-group=none
 
 /ip ipsec peer
 add name="<name of strongswan system>" address=<local IP> profile=ike2 exchange-mode=main send-initial-contact=yes
 
 /ip ipsec identity
 add peer=<remote IP of strongswan system> auth-method=pre-shared-key secret="<Put your preshared key here>" generate-policy=no
 
 /ip ipsec profile
 add name="ike2" hash-algorithm=sha1 enc-algorithm=aes-256,aes-192,aes-128,3des,des dh-group=modp2048,modp1024 lifetime=8h proposal-check=obey nat-traversal=no dpd-interval=2m dpd-maximum-failures=5

OpenVPN

Information on how to setup OpenVPN.

L2TP

Information on how to setup L2TP.

TINC

Information on how to setup tinc.

You can download tinc for *nix and Windows systems from https://www.tinc-vpn.org/

Simplified tinc 1.1 Windows setup

Examples on how to setup tinc 1.1 on Windows as either a server or client.

Server side config

Download tinc
Install tinc
Open command prompt and type the following:

   cd "C:\Program Files\tinc"
   tinc -n vpn init master
   tinc -n vpn add subnet 10.0.1.1
   tinc -n vpn add address=public.domain-or-ip
   cd tap-win64
   addtap.bat
   netsh interface ipv4 show interfaces      (Note disconnected interface.  May be called Ethernet 2)
   netsh interface set interface name = "Ethernet 2" newname = "tinc"
   netsh interface ip set address "tinc" static 10.0.1.1  255.255.255.0
   netsh interface ipv4 show config          (Should create a tinc interface with IP and subnet)
   cd ..

To start tinc:

   tincd -n vpn

To invite clients:

   tinc -n vpn invite client1

Client side config

Download tinc
Install tinc
Open command prompt and type the following:

   cd "C:\Program Files\tinc"
   tinc join <invite-url>
   tinc -n vpn add subnet 10.0.1.2
   cd tap-win64
   addtap.bat
   netsh interface ipv4 show interfaces      (Note disconnected interface.  May be called Ethernet 2)
   netsh interface set interface name = "Ethernet 2" newname = "tinc"
   netsh interface ip set address "tinc" static 10.0.1.2  255.255.255.0
   cd ..

To test connection:

   tincd -n vpn -D -d3

To run tinc as service:

   tincd -n vpn

Wireguard

Information on how to setup Wireguard.

Other

Any other information that doesn't fit elsewhere.

VPN

Contents

VPN