ASL-Corp members, Bureaucrats, Check users, Structured Discussions bots, oversight, Suppressors, Administrators, Upload Wizard campaign editors
1,714
edits
Changes
Jump to navigation
Jump to search
mLine 1:
Line 1: − {{ Note|'''This document is a work in progress and should be considered a draft until this message disappears.''' }} Line 30:
Line 29: − *Set '''$ADDRESS''' to the IP address the MikroTik CHR will use+ − *Set '''$GATEWAY''' to the IP address of the Gateway the MikroTik CHR will use − − set ADDRESS="1.1.1.1" − set GATEWAY="2.2.2.2" − − − + − + Line 60:
Line 53: − + Line 86:
Line 79: + + +
no edit summary
[[Category: MikroTik]]
[[Category: MikroTik]]
__FORCETOC__
__FORCETOC__
Welcome to the MikroTik Wiki page. Here you will find items specifically about using MikoTik devices and software as it relates to Ham Radio and/or AllStarLink/PTTLink.
Welcome to the MikroTik Wiki page. Here you will find items specifically about using MikoTik devices and software as it relates to Ham Radio and/or AllStarLink/PTTLink.
apt-get install unzip
apt-get install unzip
*Then copy and run the entire block of commands below into the terminal. Verify the name of the interface in line 4 matches what your VPS uses.
*Then copy and run the entire block of commands below into the terminal
wget https://download.mikrotik.com/routeros/6.48.3/chr-6.48.3.img.zip -O chr.img.zip && \
wget https://download.mikrotik.com/routeros/6.48.3/chr-6.48.3.img.zip -O chr.img.zip && \
gunzip -c chr.img.zip > chr.img && \
gunzip -c chr.img.zip > chr.img && \
mount -o loop,offset=33554944 chr.img /mnt && \
mount -o loop,offset=33554944 chr.img /mnt && \
ADDRESS=`ip addr show ens3 | grep global | cut -d' ' -f 6 | head -n 1` && \
ADDRESS=`ip addr show '''''ens3''''' | grep global | cut -d' ' -f 6 | head -n 1` && \
GATEWAY=`ip route list | grep default | cut -d' ' -f 3` && \
GATEWAY=`ip route list | grep default | cut -d' ' -f 3` && \
echo "/ip address add address=$ADDRESS interface=[/interface ethernet find where name=ether1] /ip route add gateway=$GATEWAY " > /mnt/rw/autorun.scr && \
echo "/ip address add address=$ADDRESS interface=[/interface ethernet find where name=ether1] /ip route add gateway=$GATEWAY " > /mnt/rw/autorun.scr && \
umount /mnt && \
umount /mnt && \
echo u > /proc/sysrq-trigger && \ dd if=chr.img bs=1024 of=/dev/vda
echo u > /proc/sysrq-trigger && \ dd if=chr.img bs=1024 of='''''/dev/vda'''''
*Once you successfully complete the above, power off (do not shut down) the VPS and then turn it back on to boot into MikroTik CHR.
*Once you successfully complete the above, power off (do not shut down) the VPS and then turn it back on to boot into MikroTik CHR.
*If the above does not work on setting the IP address and gateway properly:
*If the above does not work on setting the IP address and gateway properly:
**Set IP address with: '''/ip addres interface=ether1 add address=<ip address> netmask=<netmask>'''
**Set IP address with: '''/ip address add address=<ip address> netmask=<netmask> interface=ether1'''
**Set Gateway IP address with: '''/ip route add dst-address=0.0.0.0/0 gateway=<gateway IP>'''
**Set Gateway IP address with: '''/ip route add dst-address=0.0.0.0/0 gateway=<gateway IP>'''
*[[VPN#strongSwan to MikroTik|strongSwan to MikroTik]] - Information on connecting MikroTik to a system running the strongSwan IPSEC software
*[[VPN#strongSwan to MikroTik|strongSwan to MikroTik]] - Information on connecting MikroTik to a system running the strongSwan IPSEC software
= Wireguard =
The Mikrotik Wireguard Road Warrior Install is located at [[VPN#Mikrotik_Wireguard_Road_Warrior_Config|Mikrotik Wireguard Road Warrior Setup]].
= HamWAN =
= HamWAN =