36
edits
Changes
Jump to navigation
Jump to search
Line 280:
Line 280: − + − + Line 288:
Line 288: − + − + − + − + − + − + − − + − + − + Line 328:
Line 327: − Line 335:
Line 333: − + Line 346:
Line 344: −
no edit summary
===Serial #===
===Serial #===
Sets the serial number for the RTCM/VOTER.
Sets the serial number for the RTCM/VOTER.
*This sets the MAC address of the unit
*This sets the MAC address of the unit.
*Each unit must have a unique serial number on your network segment
*Each unit must have a unique serial number on your network segment.
===VOTER Server Address (FQDN)===
===VOTER Server Address (FQDN)===
===VOTER Server Port===
===VOTER Server Port===
This is the UDP port that the Asterisk server is listening on for clients.
This is the UDP port that the Asterisk server is listening on for clients.
*Typically it is left at the default of port 667
*Typically it is left at the default of port 667.
*'''MUST''' match the ''port'' directive in ''voter.conf''
*'''MUST''' match the ''port'' directive in ''voter.conf''.
===Local Port (Override)===
===Local Port (Override)===
Sets the local unit UDP port to be something different.
Sets the local unit UDP port to be something different.
*This is typically not used and left at default (0)
*This is typically not used and left at default (0).
===Client Password===
===Client Password===
This is the '''unique''' password for this unit.
This is the '''unique''' password for this unit.
*Every unit '''must''' have a '''unique''' password
*Every unit '''must''' have a '''unique''' password.
*'''MUST''' match the password on the client configuration line in ''voter.conf''
*'''MUST''' match the password on the client configuration line in ''voter.conf''.
===Host Password===
===Host Password===
This is the password of the Asterisk server.
This is the password of the Asterisk server.
*Configured with the ''password'' directive in ''voter.conf''
*Configured with the ''password'' directive in ''voter.conf''.
===Tx Buffer Length===
===Tx Buffer Length===
This is the size of the TX buffer from the RTCM/VOTER to the Asterisk server.
This is the size of the TX buffer from the RTCM/VOTER to the Asterisk server.
*Tuned parameter, set via the tuning instructions based on network configuration
*Tuned parameter, set via the tuning instructions based on network configuration.
===GPS Data Protocol (0=NMEA, 1=TSIP)===
===GPS Data Protocol (0=NMEA, 1=TSIP)===
Type of GPS connected.
Type of GPS connected.
*NMEA for all non-Trimble GPS units
*NMEA for all non-Trimble GPS units.
*TSIP to use with Trimble GPS that use Trimble Serial Interface Protocol (TSIP)
*TSIP to use with Trimble GPS that use Trimble Serial Interface Protocol (TSIP).
===GPS Serial Polarity (0=Non-Inverted, 1=Inverted)===
===GPS Serial Polarity (0=Non-Inverted, 1=Inverted)===
===External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted)===
===External CTCSS (0=Ignore, 1=Non-Inverted, 2=Inverted)===
If you are using the CTCSS input from an external CTCSS decoder, adjust this for your logic polarity, or set to 0 (ignore) if not used.
If you are using the CTCSS input from an external CTCSS decoder, adjust this for your logic polarity, or set to 0 (ignore) if not used.
===COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver)===
===COR Type (0=Normal, 1=IGNORE COR, 2=No Receiver)===
===Debug Level===
===Debug Level===
Set the Debug Level, if needed, based on the [[#Debug Options | Debug Options]] below
Set the Debug Level, if needed, based on the [[#Debug Options | Debug Options]] below.
===Alt. VOTER Server Address (FQDN)===
===Alt. VOTER Server Address (FQDN)===
If the firmware supports DSP/BEW Mode, set this to 1 to enable it, if desired.
If the firmware supports DSP/BEW Mode, set this to 1 to enable it, if desired.
*DSP/BEW firmware versions use extra firmware space and will make the diagnostic menu unavailable.
*DSP/BEW firmware versions use extra firmware space and will make the diagnostic menu unavailable.
==="Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs)===
==="Duplex Mode 3" (0=DISABLED, 1-255 Hang Time) (1/10 secs)===