Difference between revisions of "Radio Connections"

From "PTTLink Wiki"
Jump to navigation Jump to search
m
Line 13: Line 13:
 
Information regarding the DMK URI/URI X can be found [[URI|here]].
 
Information regarding the DMK URI/URI X can be found [[URI|here]].
  
==Modified CM108/CM119 USB FOB==
+
=Modified CM108/CM119 USB FOB=
 
{{ Note|This solution is for advanced users and requires a steady hand and microsoldering experience. }}
 
{{ Note|This solution is for advanced users and requires a steady hand and microsoldering experience. }}
 
You can purchase an unmodified CMXXX USB sound card and solder GPIO directly for COS, PTT, and CTCSS. However, it's not for the faint of heart. Doing this requires a steady hand and magnification equipment to solder to the tiny leads on the circuit board.
 
You can purchase an unmodified CMXXX USB sound card and solder GPIO directly for COS, PTT, and CTCSS. However, it's not for the faint of heart. Doing this requires a steady hand and magnification equipment to solder to the tiny leads on the circuit board.

Revision as of 05:19, 14 July 2021

Instructions for connecting radios, repeaters and PTTLink interfaces including the RTCM, GPS, URI/URI X and like devices.

RTCM/VOTER

See the RTCM page for detailed information about the RTCM/VOTER interface, used primarily to build a voting repeater system. Also note there is model specific radio information below on this page that also discusses connecting to the RTCM/VOTER.

GPS

URI / URI X

Information regarding the DMK URI/URI X can be found here.

Modified CM108/CM119 USB FOB

This solution is for advanced users and requires a steady hand and microsoldering experience.

You can purchase an unmodified CMXXX USB sound card and solder GPIO directly for COS, PTT, and CTCSS. However, it's not for the faint of heart. Doing this requires a steady hand and magnification equipment to solder to the tiny leads on the circuit board.

Radio Interface Cables (URI Cables)

KE6PCV's URI Cables are custom-made cables for many radios. If you don't want to deal with the tedium of soldering cables for your radio interface to your radio, this is the option for you. They can be used with the Master's Communications RA and DA adapters and URI/URI-X adapters. Cable selection includes:

  • Yaesu FT-2600M
  • Yaesu FT-7800
  • Yaesu FT-8800R
  • Kenwood TM-V7A
  • Kenwood TM-D700

... and many more

Motorola

CDM

CDMs make great nodes. This eBay reseller has very nice cables. Use to connect to URI or RTCM.

CDM Cable from Kurt Meltzer ex-WB9KNX, now KC4NX - Cable 83 has only one output to use for either COS or CTCSS. Use another cable if you need both COS and CTCSS.

Maxtrac

The venerable Maxtrac is a radio that was very well built, apparently has very stable reference LO, and can take a beating. When aligned properly, and sufficient *vectored* cooling is made, this radio will last for a very long, time even under several hours with of transmitting per day.

The radio will need to be aligned, and programmed to the frequenc(y/ies) you want to use. You will also need to program the Accessory Option for PL/DPL & CSQ Output.

  • Most URIs can accept active high or active low for valid RX signal detection, ie, open squelch. It is HIGHLY recommend in any situation COS is set to USB or active high. This will prevent issues. Too many to mention.
  • It is a good idea to program pin 8 on the Maxtrac/GM300 for PL/DPL & CSQ output, active high. This will cause the radio to emit a 5Vdc signal when the squelch is open, and go low when squelch is closed.

TX/RX audio, COS, and PTT connections

With the radio facing you in normal operating positing, volume knob on top left, and mic connection right below it, turn the radio over from the right side. The accessory connector is located on the rear, right top of the radio at this point. Starting from left to right, the pins on the top are / and the pins on the bottom are /. If you want to hear audio from the radios speaker, just a header jumper on the far right pins 15 and 16.


This section is a work in progress.

References: The GM300 section has the link for further reading; the Maxtrac and GM300, are relatively close in design.

MTR-2000

Quantar

The Quantar can be tricky to interface as it's extremely programmable and you will need a wireline card for I/O connections. By default the I/O will not work unless the "wildcard" table is programed. This wildcard table is Boolean logic of interrupt states in the radio, is extremely flexible and frustrating to debug. It's a base station in it's own class.

Front of Quantar and controller

Note you will want to use BEW mode on the RTCM if using the RTCM do squelch.

Also see the dedicated Quantar RTCM page for detailed information.

Syntor X

The Motorola Syntor X with an Xcat installed makes a great frequency agile remote base. For more information see this Syntor Xcat page.

VRM-850

GM300

These older radios are fairly common and easily to come by due to the narrow banding. Probably the hardest part is finding a computer and the RSS to program them. The Gm300 family has many different configurations, from low band VHF, to 800 Mhz. But the easiest variant of the GM300 is ones with the 16 pin connector. All about GM300 Radios

Connections are fairly simple but can be hard to determine which is the correct one to use. This link is a good place to start.

Kenwood

TKR720/820

Connections to: PTT, COS, RX audio out and MIC audio in

TX/RX board, MIC audio input, pins 4 & 5: floating ground, must not tie to any other ground! Some installations may require a 10dB, resistor L-network consisting of a 4.7k and 470 ohm resistors. The 470 ohm resistor connection across pins four and five, the 4.7k resistor is soldered to pin 5 to which your TX audio from the URI will connect to.

The MIC audio gain, deviation, and balance adjustments are *very* sensitive!

- RA-35 without TX adj. trimmer pots: Using a service monitor with deviation metering, start low and work your way up to 3KHz deviation with 1KHz tone, generated by simpleusb-tune-menu. If enabled, *904 turns this tone on and off by command, ie, no tone time-out as in simpleusb-tune-menu.

Baofeng

Baofeng 888

Baofeng UV82

TKR750/850

Using the Masters Communications RA-35 or RA-40 radio adapters with the TKR750/850

Repeater Controller

An example of using RTCMs to replace 420 links

Spectra Engineering

  • MX800 Base station - Bryan Fields, W9CR has a complete setup guide for the MX800 Base station which includes fallback to the built in controller and an audio delay module.

Tait

Beagle Board

The Beagle Board XM project.

Lox board

The Level One eXpansion board.

SHARI/DINAH/BRIAN USB & Pi Hats

The SHARI is a popular interface for the Pi that comes in both USB and Pi Hat versions. This is recommended for users who want to DIY a micronode for use inside a home.

Yaesu

FT 7900/8900

Both models sport a mini-DIN 6 pin connector on the rear panel. These can easily be hooked into a URI of your choice, such as a DRA-50 and an appropriate cable. This is a nearly plug & play solution for this radio.

Masters Communications RA-Series Radio Adapters

Inexpensive but feature rich USB Radio Adapters for PTTLink.

Vertex

Quad Radio PCI card

Modified USB FOB